Updated November 2026

Replacing a kitchen sink faucet is a manageable weekend project if you work methodically. In this guide you will shut off the water safely, remove the old faucet, mount the new one and check for leaks before you finish. Most standard single-hole and three-hole faucets follow the same basic sequence.

Prepare the Sink and Gather Tools

Start by closing the shutoff valves under the sink, then open the faucet to drain the remaining water. Clear the cabinet so you can reach the connections comfortably. Keep a bucket and towels nearby, since some water always stays in the supply lines.

Shopping for one? See our guide: 5 Best Faucets for Kitchen Sink Options Compared for Every Need (2026).

  • Adjustable wrench and basin wrench
  • Plumber’s putty or a silicone gasket, depending on the faucet
  • Flashlight and bucket
  • Replacement supply lines if the old ones are cracked or stiff
  • Penetrating lubricant for corroded nuts

Remove the Old Faucet

Disconnect the supply lines first, then the mounting nuts underneath the sink deck. A basin wrench reaches the nuts that a regular wrench cannot. If the nuts are seized, apply penetrating lubricant and wait about 15 minutes before trying again. Lift the old faucet out and scrape away old putty or gasket residue so the new faucet seats flat. For a more detailed walkthrough, see How to Remove a Kitchen Sink Faucet: A Step-by-Step Guide.

Install the New Faucet

Read the manufacturer’s instructions before assembling anything, because mounting hardware differs between brands. Set the new faucet in place, seal the base as specified, and tighten the mounting nuts from underneath until the faucet is firm but not overtightened. Connect the hot and cold supply lines and the drain assembly, keeping the connections hand-tight before giving them a final quarter turn with a wrench. If your faucet has a sprayer or a separate hose, route it before tightening the deck nuts. For a full installation walkthrough, read How to Install a Kitchen Sink Faucet: A Step-by-Step Guide for Beginners.

Test for Leaks and Finish Up

Open the shutoff valves slowly, one at a time, and watch each connection. Run the faucet on hot and cold for two to three minutes, then check the supply line nuts, the base and the drain for drips. Tighten any connection that seeps, but do not crank it down hard, since that can crack plastic nuts and washers. Once the faucet runs clean, wipe the surfaces dry and check the flow and temperature response.

Know When the Problem Is Smaller

If your existing faucet only drips or has weak flow, you may need a repair rather than a full replacement. Replacing only the cartridge can be enough, as covered in Replacing Kitchen Faucet Cartridge: A Step-by-Step Guide for Beginners. A replacement head can also solve spray problems, as explained in Replacing Kitchen Faucet Head: A Step-by-Step Guide (2026).

Common Mistakes

  • Skipping the shutoff valves and getting soaked when the supply lines disconnect.
  • Forgetting the gasket or putty, which causes leaks at the sink deck.
  • Overtightening plastic nuts, which can crack them.
  • Reusing old supply lines that show cracks or bulging.
  • Buying a faucet without checking the sink’s hole count and deck thickness.

A basin wrench makes the mounting nuts far easier to reach in a tight cabinet. View on Amazon

Braided stainless steel supply lines are a common upgrade when replacing the old hoses at the same time. View on Amazon

Plumber’s putty seals the faucet base cleanly on sinks that call for it. View on Amazon

FAQ

Do I need a plumber to replace a kitchen sink faucet?

Many homeowners handle this themselves, since the work involves basic tools and simple connections. If you find corroded pipes, a damaged sink, or no shutoff valves, consult a licensed plumber.

How long does the job usually take?

Most people finish a standard replacement in one to two hours, though a seized old faucet can add time. Plan for extra time if the cabinet is cramped.

Can I reuse the old supply lines?

You can reuse them only if they are flexible and free of cracks or leaks. Replacing them is inexpensive insurance against future drips.

Conclusion

Replacing a kitchen sink faucet comes down to shutting off the water, removing the old unit, mounting the new one and testing every connection. Take your time with the nuts and seals, and check for leaks before you call the job finished. With careful preparation, the whole project is usually a single afternoon.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.