Updated November 2026

Delta kitchen faucet removal is a manageable job for most homeowners with basic hand tools. In this guide, you’ll shut off the water, disconnect the supply lines, release the mounting hardware and lift the faucet out of the sink. Plan on an hour or so, and expect the nuts under the sink to be the hardest part.

Before You Start: Shut Off the Water

Look under the sink for the two angle stop valves, one for hot and one for cold. Turn them clockwise until they stop. Then turn on the faucet to drain the remaining pressure and water in the lines. Keep a bucket and towels under the sink, since a little water will still come out of the supply lines when you disconnect them.

Shopping for one? See our guide: 7 Best Delta Kitchen Faucet Parts (2026): Repair-Ready Picks.

Disconnect the Supply Lines and Sprayer Hose

Use an adjustable wrench or basin wrench to loosen the nut where each supply line meets the faucet shank. Hold the valve steady with a second wrench so you don’t twist the pipe. If your Delta has a pull-out sprayer, unclip the hose from the docking clip under the sink and feed the hose back through the deck hole. Some models use a quick-connect fitting for the sprayer, which you can release by pressing the tab while pulling the hose.

Release the Mounting Nut and Lift the Faucet

Under the sink, you’ll find a plastic or metal mounting nut on the threaded shank of the faucet. Reach up with a basin wrench and turn it counterclockwise. Some installations use a locknut and a mounting plate, so remove those as well. Once the nut is loose, go upstairs to the sink deck and lift the faucet straight up and out, guiding the supply lines and sprayer hose through the holes.

Tips for a Stuck Mounting Nut

Corrosion and old plumber’s putty can seize the nut. Spray a penetrating lubricant onto the threads, wait about 15 minutes, and try again. Tap the wrench lightly with a hammer if needed to break the bond. Avoid heavy force on plastic nuts, which can crack.

Clean the Deck and Prepare for Reinstallation

With the faucet removed, scrape away any old putty or sealant from the sink deck. Clean the surface so the new faucet or gasket seats properly. If you plan to reinstall the same unit, label the supply lines and note how the hoses route, which will save time later. If you’re replacing the faucet entirely, compare your sink’s hole configuration first. For help choosing a replacement, see Delta Kitchen Faucet with Pull-Out Sprayer Review: Features and Performance.

Common Mistakes to Avoid

  • Skipping the water shutoff, which can leave you with a soaked cabinet.
  • Twisting the supply lines instead of holding the valve with a second wrench.
  • Forcing a plastic mounting nut that cracks under pressure.
  • Forgetting the sprayer hose, which can snag and damage the deck or other parts.
  • Reconnecting the supply lines without checking for leaks before closing the cabinet.

A basin wrench reaches the mounting nut in tight spaces under the sink, where a standard wrench can’t fit. View on Amazon

A penetrating lubricant helps loosen corroded nuts and fittings without forcing them. View on Amazon

An adjustable wrench is useful for holding and turning supply line connections. View on Amazon

FAQ

Do I need to turn off the main water supply?

You usually don’t need to, since the angle stop valves under the sink isolate the faucet. If those valves are old or fail to close fully, shut off the main water supply to your home instead.

Can I remove a Delta faucet without a basin wrench?

You can, but it’s harder. A basin wrench is designed for the tight space under the sink, so it makes reaching the mounting nut much easier.

What should I do if water keeps leaking after I reconnect the lines?

Turn the water off, check that each supply line nut is snug without being overtightened, and inspect the washers. If the leak continues, consult a licensed plumber for help.

Conclusion

Removing a Delta kitchen faucet comes down to shutting off the water, disconnecting the lines and sprayer hose, and releasing the mounting nut. Work patiently with corroded hardware, and protect the sink deck and cabinet as you go. With those steps done, you’re ready to install a replacement or repair the existing unit.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.