Updated November 2026

To repair a faucet that drips, you shut off the water, take the handle apart, find the worn part causing the leak, and replace it. Most drips come from a worn washer, an O-ring or a cartridge, and a basic set of hand tools is enough for the job. Plan on about an hour for a standard compression or cartridge faucet, including time to find the right replacement part.

Identify the Type of Faucet First

The repair depends on which faucet design you have, so check that before you take anything apart. A compression faucet has two separate handles, one for hot and one for cold, and uses rubber washers that press against a valve seat. A cartridge faucet, common on single-handle kitchen models, uses a sealed plastic or brass cylinder that controls the flow. A ball faucet has a single handle on a rounded metal ball with several rubber seals. Look at the handle and the way the water flows when you turn it to narrow things down. Manufacturers such as Delta, Moen and Kohler each use their own internal parts, so match the replacement to your brand and model number whenever possible.

Shopping for one? See our guide: 6 Best Tub Faucet Repair Kits for Leaks and Drips (2026).

Step-by-Step Repair Process

Start by shutting off the water supply under the sink. Turn the valves clockwise until they stop, then open the faucet to drain the remaining water. Next, follow these steps:

  1. Pry off the decorative cap on the handle, then remove the handle screw and lift the handle off.
  2. Unscrew the packing nut or retaining nut with an adjustable wrench, wrapping tape around the jaws to avoid scratches.
  3. Remove the stem or cartridge. For compression faucets, the stem sits inside the body. For cartridges, it usually lifts straight out after a retaining clip is removed.
  4. Inspect the washer, O-ring and valve seat. A washer that is flattened, cracked or pitted is the most common cause of a drip.
  5. Replace the worn part with an exact match. Take the old washer or cartridge to the hardware store if you are unsure.
  6. Reassemble in reverse order, turn the water back on slowly, and test the faucet at both full-open and fully closed positions.

Clean the Valve Seat

If the drip continues after you replace the washer, the valve seat may be scored or coated with mineral deposits. Use a seat wrench or a small screwdriver to remove the seat, then clean the threads and the seat surface. Hard water deposits often cause the leak to return within weeks if they are not removed.

When to Replace the Whole Cartridge or Stem

If the cartridge shows cracks, scratches on the sealing surface, or stiff, jerky handle movement, replacing the entire unit is more reliable than trying to repair it. Many owners report that a worn cartridge keeps dripping even after a new O-ring is installed. A replacement cartridge that matches your faucet brand and model number typically solves the problem for good.

Faucet type Most likely cause of drip Typical fix
Compression Worn washer or valve seat Replace washer, clean or replace seat
Cartridge Worn cartridge or O-rings Replace cartridge or O-ring kit
Ball Worn seats or springs Replace seats, springs and O-rings

For more on specific brands and kits, see Replace Kitchen Faucet Cartridge: Step-by-Step Repair Guide and 5 Best Kitchen Faucet Repair Kits for Leaks and Drips (2026). If your leak is at the tub spout rather than the sink, Repair Tub Faucet Drip: A Step-by-Step Guide to Stop Leaks (2026) covers that setup.

  • Adjustable wrench: Loosens packing nuts and retaining nuts without damaging the finish. View on Amazon
  • Faucet repair kit: Bundles common washers, O-rings and seals so you can match parts quickly. View on Amazon
  • Plumber’s tape: Helps seal threaded connections when you reassemble the faucet. View on Amazon

Common Mistakes

  • Skipping the water shutoff, which can soak the cabinet and make the job messier.
  • Using a wrench with sharp jaws on a chrome finish, which leaves marks.
  • Replacing a washer with one of a different size or thickness, which keeps the leak going.
  • Overtightening the handle screw, which can crack the stem.
  • Forgetting to check the O-rings, which are often the real source of a leak at the base of the handle.

FAQ

Why does my faucet keep dripping after I replaced the washer?

The valve seat may be scored or coated in mineral deposits, which a new washer cannot seal against. Clean or replace the seat, and check that the washer is the correct size.

Do I need to turn off the water main to fix a dripping faucet?

Usually not. Closing the shutoff valves under the sink is enough for most kitchen and bathroom faucets.

When should I call a professional plumber?

If the valves under the sink leak, if the faucet body is corroded or cracked, or if you are unsure about shutting off the supply, consult a licensed plumber.

Conclusion

Most dripping faucets can be repaired in an hour with basic tools and the correct replacement part. Identify your faucet type, replace the worn washer, O-ring or cartridge, and test the result carefully. Keep your model number handy so the parts you buy match your faucet exactly.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.