Updated November 2026
To remove the aerator from a Delta faucet, unscrew the small mesh cap at the tip of the spout by hand or with a cloth-wrapped grip, then pull out the screen and washer. You can clean or replace the parts in about ten minutes without shutting off the water supply. This guide covers the steps, common snags and tips for reinstalling the aerator so it doesn’t leak.
What You Need Before You Start
Most Delta aerators come off by hand, but a few tools make the job easier, especially if mineral deposits have sealed the threads.
Shopping for one? See our guide: Delta Faucet Screen Replacement: 7 Best Aerator Screens Compared.
- A soft cloth or rubber gripper pad to protect the finish
- An adjustable wrench or pliers wrapped in tape or cloth
- White vinegar and a small brush or old toothbrush
- A small bowl to catch the parts
- A replacement aerator of the same size, if the old one is damaged
Step-by-Step: How to Remove Delta Faucet Aerator Parts
Work over a sink with a drain stopper in place, or cover the drain, so a dropped screw or washer doesn’t disappear.
- Check the spout tip. Look for a small rounded cap with a knurled edge. This is the aerator housing.
- Wrap the housing. Put a cloth or rubber pad around it to prevent scratches on the chrome or brushed finish.
- Turn counterclockwise. Grip firmly and turn the housing to the left. If it doesn’t move, apply gentle pressure with a wrench wrapped in cloth and try again.
- Remove the parts in order. Lift out the outer cap, then the mesh screen, any plastic or rubber seal, and the inner flow restrictor if present. Keep them in the order you removed them.
- Inspect each piece. Note any grit, flaking or warped washers.
If the Aerator Is Stuck
Mineral scale is the usual cause. Soak the housing in white vinegar for 20 to 30 minutes, then try again. Owners often report that a second attempt works after a soak, while forcing it tends to crack the plastic parts or scratch the finish.
Cleaning and Reinstalling the Aerator
Rinse the mesh screen under running water, scrubbing away sediment with a soft brush. Soak small parts in vinegar if you see white or green deposits. Replace the screen or washer if it is torn, stiff or no longer sits flat.
To reinstall, put the parts back in the same order you removed them. Hand-tighten the housing clockwise until snug. Avoid overtightening, which can distort the washer and cause drips. Then run the water for about 30 seconds to flush any remaining debris.
Common Mistakes to Avoid
- Using pliers directly on the chrome without a cloth wrap, which leaves marks.
- Reversing parts, such as putting the screen above the seal, which causes spraying or weak flow.
- Skipping the drain cover, so small parts fall down the drain.
- Overtightening the housing, which can crack plastic components.
- Forgetting to flush the line after reinstalling, leaving sediment in the stream.
Recommended Gear
A rubber gripper pad helps you turn a stubborn aerator housing without marring the finish. Choose one sized for small fittings.
A soft-jaw adjustable wrench lets you apply firm turning force while protecting the chrome. Wrap the jaws in tape or a cloth before use.
FAQ
Do I need to shut off the water to remove the aerator?
No. The aerator unscrews while the faucet is off, and the water pressure at the tip is low enough that you won’t get a major spray. Turn the faucet off before you start to avoid splashing.
Can I use the same aerator after cleaning it?
Yes, if the screen is intact and the washers are flexible. Replace any cracked or deformed parts, since worn components often cause leaks or uneven flow.
What if the aerator is broken or I can’t get it out?
Soak it in vinegar and try again with a cloth-wrapped grip. If the housing still won’t move or the threads are damaged, a plumber or the faucet manufacturer’s support team can advise you on next steps.
Conclusion
Removing a Delta faucet aerator takes only a few minutes with a cloth-wrapped grip and a vinegar soak for stubborn deposits. Clean the screen, reinstall the parts in order and hand-tighten for a clean stream. Regular cleaning every few months helps keep flow strong and prevents buildup.
