Updated November 2026

Most Delta faucet handles are held in place by a small hex set screw, and the wrench that fits it is usually a 3/32-inch Allen wrench. Some models, especially older or specific series, use a 1/8-inch or 5/64-inch hex key instead, so measuring the screw before you start saves you from stripping it. This guide explains how to identify the correct size, loosen the handle, and avoid the mistakes that cause the most trouble.

Identify the Correct Allen Wrench Size

Start by checking the screw itself. Delta handle set screws sit on the underside or side of the handle, often under a small decorative cap or cover. Lift or pry off the cap gently with a flathead screwdriver or a fingernail, then look for a hexagonal socket.

Shopping for one? See our guide: 6 Best Delta Faucet Replacement Parts (2026): Expert Picks.

Test the fit with a set of metric or SAE hex keys rather than guessing. A correct key should slide fully into the socket with no visible gap, and it should feel snug when you press it in. If the key wobbles or only grips the top edge, try the next size up or down.

Common sizes to try first

  • 3/32 inch: the most frequent size on single-handle kitchen and lavatory faucets
  • 1/8 inch: common on some older Delta models and certain handle styles
  • 5/64 inch: appears on select compact or specialty handles

Loosen and Remove the Handle

  1. Turn off the water supply under the sink. If you are not sure which valve to close, turn off the main supply at the house.
  2. Open the faucet to release any remaining pressure and water in the lines.
  3. Pop off the decorative cap or button cover on the handle.
  4. Insert the correct hex key into the set screw and turn counterclockwise. Most set screws only need a quarter to half turn before they release.
  5. Lift the handle straight up. Do not rock it side to side, which can crack the plastic or damage the cartridge stem underneath.

Reinstall the Handle Without Damage

Reverse the process once your repair or cleaning is finished. Set the handle back on the stem, aligning the index marks so the handle points in the correct direction. Tighten the set screw clockwise until it is snug, then stop. Overtightening can crack the handle body or strip the threads, which is a far bigger problem than a loose handle.

Check the handle for smooth operation before replacing the cover cap. It should turn freely through its full range with no grinding, and the hot and cold positions should match the labels.

Common Mistakes

  • Using a worn or rounded hex key. Replace it if the tips look shiny or flattened.
  • Forcing a key into a socket that does not fit, which can round the screw head.
  • Skipping the water shutoff, leading to a spray of water when the cartridge is exposed.
  • Assuming all Delta faucets share one size. Verify each handle individually.
  • Using a standard screwdriver on the set screw, which slips and damages the surrounding finish.

A metric and SAE hex key set lets you test several sizes quickly without hunting for individual wrenches. View on Amazon

A small flathead screwdriver or plastic trim tool helps lift the decorative cap without scratching the finish. View on Amazon

FAQ

What Allen wrench size fits most Delta faucets?

Many Delta handles use a 3/32-inch hex key, but 1/8-inch and 5/64-inch sizes also appear on certain models. Test the socket fit before applying force.

Do I need to turn off the water to remove the handle?

It is strongly recommended. Turning off the supply prevents a sudden spray when the cartridge is exposed and makes the job cleaner.

What if the set screw is stuck or stripped?

Apply a small amount of penetrating lubricant and wait several minutes before trying again. If the screw is badly stripped, a licensed plumber can remove it safely and avoid damaging the faucet.

Conclusion

Matching the hex key to the set screw is the most important step in removing a Delta faucet handle cleanly. Test sizes carefully, shut off the water, and tighten gently when reinstalling. Once the handle is off, you can move on to cartridge or stem work with confidence.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.