Updated November 2026

A delta tub faucet dripping usually comes down to one worn part: the cartridge, a rubber seal or a valve seat. In most cases you can stop the drip in under an hour with a few basic tools, a replacement cartridge and a bit of patience. This guide walks through diagnosis, shutoff, disassembly and reassembly so you can fix the leak on your own.

Find Out Where the Drip Is Coming From

Before you take anything apart, figure out which part is failing. Run the tub for a few seconds, then shut it off and watch the spout. If water keeps trickling from the spout, the cartridge is likely the culprit. If the leak is at the handle or the base, look at the O-rings and the stem seals instead. Water dripping from the showerhead when the diverter is off points to the diverter valve.

Shopping for one? See our guide: 4 Best Delta Wall Mounted Tub Faucets Compared (2026).

Delta tub faucets come in several designs, including single-handle and two-handle styles. Owners often report that the cartridge is the most common source of a steady drip, but it helps to confirm the model before you order parts.

Shut Off the Water and Remove the Handle

  1. Shut off the hot and cold supply valves under the tub or at the main line. If the valves are stiff or do not close fully, shut off the main water supply to the house.
  2. Open the faucet to drain remaining water and release pressure.
  3. Pry off the decorative handle cap with a flat screwdriver. Wrap the blade in painter’s tape to avoid scratching the finish.
  4. Remove the handle screw, usually a Phillips or hex screw, and lift the handle off the stem.
  5. Unscrew the trim plate and the bonnet nut. A cartridge puller or an adjustable wrench with a cloth wrap works well here.

Replace the Cartridge and Seals

Pull the cartridge straight out of the body. Many Delta cartridges have a retaining clip at the top that you must remove first. Take the old cartridge to the store or match the model number so you buy the correct replacement. Using the wrong cartridge is one of the most common reasons a repaired faucet keeps dripping.

Before you install the new cartridge, inspect the valve seat inside the body. If you see grit, mineral buildup or pitting, clean it with a soft cloth or a valve seat wrench. Replace the O-rings on the new cartridge or the stem, and coat them with plumbers’ silicone grease. Dry rubber seals wear out quickly and can cause new leaks.

Manufacturers specify that cartridges must sit fully seated and aligned with the handle index. Push the cartridge in until it stops, reinstall the clip and check that the hot and cold indicators line up.

Reassemble and Test the Faucet

Reverse the disassembly steps. Tighten the bonnet nut snugly, but do not overtighten it, since this can crack the body or strip the threads. Reattach the handle and cap, then slowly open the supply valves. Run the tub on both hot and cold and check the spout for any remaining drip.

Checklist before you start

  • Adjustable wrench and a cloth or tape to protect finishes
  • Flat-blade and Phillips screwdrivers or a hex key, depending on the model
  • Replacement cartridge matched to your Delta model number
  • Replacement O-rings and plumbers’ silicone grease
  • Bucket or towels to catch residual water

Common Mistakes

  • Skipping the shutoff. Even a small amount of water pressure can spray when the cartridge comes out.
  • Buying a cartridge by appearance instead of model number. Similar-looking cartridges often have different internal dimensions.
  • Overtightening the bonnet nut, which can damage the body or the new cartridge.
  • Reusing old O-rings. Worn seals are a frequent cause of repeat leaks.
  • Ignoring the valve seat. A cartridge will not seal properly against a pitted seat.
  • Delta replacement cartridge: Matched to your exact model, it is the part most likely to stop the drip. View on Amazon
  • Plumbers’ silicone grease: Keeps O-rings flexible and helps them seal without tearing. View on Amazon
  • Cartridge puller: Makes removing a stuck cartridge easier without damaging the faucet body. View on Amazon

FAQ

Why does my Delta tub faucet keep dripping after I replaced the washer?

Delta tub faucets generally use cartridges rather than washers, so a washer swap may not address the real problem. Check whether the cartridge is the correct model and whether the valve seat is clean.

Can I fix a dripping tub faucet without turning off the main water?

You can often shut off just the hot and cold supply valves under the tub. If those valves leak or do not close fully, shut off the main supply instead.

When should I call a plumber?

Call a licensed plumber if the supply valves will not shut off, if you see corrosion or leaks inside the wall, or if the faucet still drips after a cartridge replacement. Consult a professional before working with gas lines or electrical components nearby.

Conclusion

Most delta tub faucet dripping problems come down to a worn cartridge, damaged seals or a rough valve seat. Shut off the water, identify the failing part and install a correctly matched replacement. Take your time with reassembly, and the drip should stop for good.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.