Updated November 2026
To take off a kitchen faucet, you shut off the water supply, disconnect the supply lines and spray hose, then loosen the mounting nut or nuts under the sink. Once those are free, the faucet lifts straight out of its holes. The whole job usually takes 30 to 60 minutes, and most of that time goes to reaching the fittings under the sink.
Prepare the Sink Area Before You Start
Start by clearing the cabinet under the sink and placing a towel and a shallow bucket beneath the supply lines. Old faucets often hold a cup or two of water in the lines and the body, so expect a small spill. Locate the two shutoff valves on the hot and cold supply lines, which are usually small oval handles or quarter-turn stops on the wall or floor behind the sink.
Shopping for one? See our guide: 7 Best Delta Kitchen Faucet Parts (2026): Repair-Ready Picks.
If your home has no individual shutoff valves, you will need to turn off the main water supply. Open the kitchen faucet afterward to relieve remaining pressure.
Disconnect the Lines and Remove the Faucet
- Turn both shutoff valves clockwise until they stop. Then open the faucet to confirm the water has stopped flowing.
- Loosen the compression nuts on the hot and cold supply lines with an adjustable wrench, holding the valve body steady with a second wrench so you do not twist the pipes.
- Disconnect the spray hose from the faucet body and, on pull-out models, from the weight or docking clip under the sink.
- Find the mounting hardware. Most faucets are held by a plastic or metal mounting nut on a threaded shank, or by a pair of nuts on a mounting plate. Loosen these by hand where possible, then use a basin wrench for nuts you cannot reach.
- Lift the faucet straight up and out of the sink holes. If it resists, check for remaining caulk or a leftover nut before pulling harder.
Deal with Stuck Nuts and Old Caulk
Nuts that have sat for years can seize from mineral buildup. Apply penetrating oil and wait 10 to 15 minutes before trying again. Use steady pressure rather than sudden jerks, which can crack a plastic nut or strip the threads on the shank.
Caulk between the faucet base and the sink deck also holds the faucet in place. Score it with a utility knife and peel it away. Clean the deck thoroughly so the new faucet seats flat.
Common Mistakes
- Skipping the shutoff valves and relying on the faucet handle alone, which leads to a wet cabinet floor.
- Forcing a seized nut with pliers, which can damage the sink or the faucet body.
- Pulling a pull-out spray head through the sink hole without first disconnecting the hose from the weight.
- Leaving the supply lines bent or kinked, which can crack them when you reattach.
- Forgetting to note how the faucet was mounted, including the order of washers and gaskets.
Recommended Gear
A basin wrench reaches mounting nuts tucked against the back of the sink, where a standard wrench cannot fit. View on Amazon
Penetrating oil loosens corroded threads and seized nuts without scraping the finish. View on Amazon
An adjustable wrench with a wide jaw handles compression nuts on supply lines without rounding the corners. View on Amazon
FAQ
Do I need to turn off the main water to remove a kitchen faucet?
Not usually. If the sink has working shutoff valves on the hot and cold supply lines, closing those is enough. Only shut off the main if the valves are missing or leaking.
Can I reuse the old supply lines when I reinstall?
Often yes, if they are not kinked, cracked or corroded. Many plumbers replace them anyway, since they are inexpensive insurance against a leak.
What if the faucet will not lift out of the holes?
Check for leftover mounting nuts, dried caulk or a spray hose still attached underneath. If it is still stuck, consult a licensed plumber rather than prying hard enough to damage the sink.
Conclusion
Once the water is off and the supply lines are disconnected, taking off a kitchen faucet comes down to loosening the mounting hardware and lifting it out. Work slowly around seized nuts and old caulk, and take a photo of the mounting setup before you start. That photo will help you install the replacement correctly.
