Updated November 2026

Replacing a faucet kitchen unit is a manageable weekend project if you work methodically. In this guide you will shut off the water safely, remove the old faucet, mount the new one, connect the supply lines and check for leaks. Most homeowners need only basic hand tools and about an hour or two, though older fittings can slow things down.

Before You Start: Gather Tools and Check Fit

Confirm that the new faucet matches your sink. Single-hole, three-hole and wall-mount layouts each require a different setup, so check the number of holes and their spacing before you buy. If you are unsure about the layout, read the guide on Two-Handle Kitchen Faucets: Layout, Holes and Upkeep to see how holes are counted.

Shopping for one? See our guide: 7 Best Delta Kitchen Faucet Parts (2026): Repair-Ready Picks.

Gather these items before you begin:

  • Adjustable wrench and basin wrench
  • Bucket and old towels
  • Plumber’s putty or silicone sealant (check your new faucet’s instructions)
  • Flashlight
  • Replacement supply lines, if the old ones are stiff or cracked

Step-by-Step: Removing the Old Faucet

  1. Shut off the hot and cold supply valves under the sink. If the valves are stuck or do not stop the flow, shut off the main water supply.
  2. Open the faucet to drain remaining water and relieve pressure.
  3. Place a bucket under the trap and disconnect the supply lines with your wrench.
  4. Loosen the mounting nuts beneath the sink with a basin wrench. Lift the old faucet out and scrape away old putty or gasket residue.

If the old faucet is very stubborn, the process is similar to the one described in Take Off Kitchen Faucet: A Step-by-Step Guide for Beginners.

Installing the New Faucet Kitchen Unit

Read the manufacturer’s instructions before you mount anything. Most faucets specify a gasket or sealant type and a torque range for the mounting nuts. Overtightening can crack a sink or deform the base.

  1. Place the gasket or apply putty to the base of the faucet as directed.
  2. Feed the supply lines and any spray hose through the sink holes.
  3. Set the faucet in place and tighten the mounting nuts evenly under the sink.
  4. Connect the supply lines to the shutoff valves. Hand-tighten first, then add a quarter turn with the wrench.

Testing and Final Checks

Open the shutoff valves slowly. Run both hot and cold water for at least two minutes, then check every joint for drips. Tighten fittings only in small increments, because over-cranking plastic nuts can strip threads. Watch the water pressure too. Low flow after installation often points to a clogged aerator, which you can clean in a few minutes.

Common Mistakes to Avoid

  • Skipping the shutoff check. Confirm the water is off before you disconnect anything.
  • Reusing old supply lines that show corrosion or bulging.
  • Forgetting to clean the sink surface before applying sealant.
  • Overtightening mounting nuts, which can crack porcelain or stainless steel sinks.
  • Failing to test for leaks at low pressure before walking away.
  • Basin wrench: Reaches the mounting nuts in tight cabinet space where a standard wrench cannot fit. View on Amazon
  • Braided stainless supply lines: Resist kinking and are often easier to route than rigid lines. View on Amazon
  • Plumber’s putty: Creates a watertight seal around the faucet base on most sinks. View on Amazon

FAQ

Do I need a plumber to replace a kitchen faucet?

Many homeowners handle the job themselves if the shutoff valves work and the sink is in good condition. Consult a licensed plumber if the valves fail, pipes are corroded or you find water damage.

How long does replacing a kitchen faucet take?

Most straightforward installations take between one and two hours. Stuck nuts, tight cabinet space or damaged supply lines can add time.

Can I reuse the old supply lines?

Reuse them only if they are flexible, free of corrosion and undamaged. Replacing them is inexpensive insurance against leaks, and the manufacturer’s instructions often recommend fresh lines anyway.

Conclusion

Replacing a faucet kitchen fixture comes down to shutting off water, removing the old unit carefully, mounting the new one with the right seal and testing every connection. Take your time with the nuts and fittings, and check for leaks before you call the job finished.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.