Updated November 2026

To repair a leaking garden faucet, you need to find out where the water is escaping, shut off the supply, and replace the worn part causing the problem. Most drips come from a worn washer, a failed O-ring or a damaged seat, and each is inexpensive and simple to swap. With basic hand tools and about an hour, you can usually stop the leak completely.

Identify Where the Leak Is Coming From

Before you take anything apart, figure out whether the water is dripping from the spout when the handle is closed or leaking around the handle and stem. A spout drip points to a worn washer or seat. A leak around the handle usually means a failed packing nut or stem O-ring. Dry the faucet, turn the water on briefly, and watch closely to pinpoint the source.

Shopping for one? See our guide: 6 Best Moen Leaking Kitchen Faucet Repair Parts (2026).

Shut Off the Water and Remove the Stem

Locate the shutoff valve for the outdoor line, which is often inside the basement or crawl space, and close it fully. Then open the outdoor faucet to drain any remaining water. Once it is dry, you can work on the faucet.

  1. Remove the handle screw and lift off the handle.
  2. Unscrew the packing nut with an adjustable wrench or a faucet wrench.
  3. Pull out the stem assembly. Keep it in order so you can reassemble it correctly.
  4. Check the brass screw at the bottom of the stem and the rubber washer it holds in place.

Replace the Washer, O-Ring or Seat

Worn rubber washers are the most common cause of a spout drip. Remove the screw holding the washer, take the old washer out, and press in an identical replacement, matching the size and shape. Rub a small amount of plumber’s grease on any new O-rings before you install them. If the valve seat inside the faucet body is pitted or rough, a seat wrench can resurface or replace it. Replace the packing nut washer as well if the handle leaked.

Reassemble and Test

Reinstall the stem, tighten the packing nut snugly but do not overtighten it, and replace the handle. Slowly open the shutoff valve, then go back to the faucet and test it. If the drip continues, the seat is likely damaged and needs replacing.

  • An adjustable wrench, to loosen the packing nut without scratching the finish. View on Amazon
  • A faucet seat wrench, for removing and resurfacing a worn valve seat. View on Amazon
  • Silicone plumber’s grease, to lubricate O-rings and help them seal. View on Amazon

Common mistakes to avoid

  • Skipping the shutoff valve step, which leaves water flowing into the faucet while you work.
  • Overtightening the packing nut, which can crush the O-ring and cause new leaks.
  • Buying a washer that is slightly too large or small instead of matching the original.
  • Forgetting to drain the line, which lets trapped water spray when you remove the stem.
  • Ignoring a pitted valve seat, since a new washer alone will not stop the drip.

If your garden faucet is an older model, you may find that replacement kits are a more practical route than individual parts. For a broader look at options, see Leaking Outdoor Faucet Repair: 5 Best Kits Compared (2026) and Outdoor Faucet Leak Repair: 7 Best Kits and Parts Compared (2026). If the leak is at the handle rather than the spout, Repair Exterior Faucet Leak: 6 Best Kits and Parts Compared (2026) covers those repairs in more detail.

FAQ

Why does my garden faucet drip after it is turned off?

The most common reason is a worn rubber washer or a damaged valve seat that no longer seals against the water flow. Replacing the washer often solves the problem, but a pitted seat may need resurfacing or replacement.

Can I repair a leaking garden faucet without turning off the house water?

You can usually shut off just the outdoor line at an interior valve, so the rest of the house keeps running. If you cannot find a dedicated valve, consider calling a licensed plumber before working on a supply line.

How long does a garden faucet repair usually take?

Most repairs take between thirty minutes and an hour once you have the right parts on hand. Older or corroded faucets can take longer because stuck components may need penetrating oil or extra time to remove.

Conclusion

A leaking garden faucet is usually a simple fix once you identify the leak source and replace the worn washer, O-ring or seat. Work methodically, keep the stem parts in order, and avoid overtightening the packing nut. With the right parts and a little patience, your faucet should run dry again within an afternoon.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.