Updated November 2026
To remove a kitchen sink faucet, you shut off the water supply, disconnect the supply lines, loosen the mounting nuts under the sink and lift the faucet out. The whole job usually takes between 30 minutes and an hour, depending on how old the faucet is and how tight the nuts are. The steps below work for most single-handle and two-handle faucets with standard mounting hardware.
Before You Start: Shut Off the Water and Gather Tools
Turn off the water at the shutoff valves under the sink. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Then open the faucet to drain any remaining water and pressure from the lines.
Shopping for one? See our guide: 5 Best Faucets for Kitchen Sink Options Compared for Every Need (2026).
Lay a towel across the cabinet floor and place a bucket underneath to catch residual water. Clear out the cabinet so you can reach the back of the faucet.
How to Disconnect and Remove the Faucet
- Place a bucket under the supply line connections and use an adjustable wrench to loosen the compression nuts on the hot and cold supply lines.
- Disconnect the sprayer hose and any quick-connect fittings beneath the sink. Pull the hose down through the deck hole so it is clear.
- Find the mounting nuts or plastic retaining clips that hold the faucet base to the sink. On many models, these sit directly under the sink deck on threaded studs.
- Loosen the mounting nuts by hand as far as you can, then finish with a basin wrench. A basin wrench reaches tight, awkward spots that a standard wrench cannot.
- Lift the faucet straight up and out of the deck holes. Remove any gaskets or rubber seals that stay behind on the sink surface.
Dealing with Stuck or Corroded Nuts
Corroded mounting nuts can resist even a basin wrench. Apply penetrating oil and wait 15 to 20 minutes before trying again. Work the nut back and forth a quarter turn at a time rather than forcing it in one direction, which can crack the nut or strip the threads.
Preparing the Sink Surface for a New Faucet
Once the old faucet is out, scrape away old plumber’s putty, caulk or gasket residue. Clean the deck around each hole with a non-abrasive cleaner so the new faucet seats flat. If the holes are the wrong size or spacing for a replacement, check the new faucet’s hole requirements before you buy it. Our guide to choosing a kitchen faucet by how you use your sink covers hole counts and layouts in more detail.
Tools and Supplies Checklist
- Adjustable wrench or basin wrench
- Bucket and towels
- Penetrating oil
- Plastic scraper or old toothbrush for cleaning residue
- Flashlight or headlamp for the cabinet
- Replacement supply lines, if the old ones are cracked or stiff
Common Mistakes to Avoid
- Skipping the water shutoff. Test the faucet by opening it after closing the valves to confirm the lines are dry.
- Forcing a corroded nut with a pipe wrench, which can damage the sink or supply line.
- Losing track of small clips and washers. Set them on a towel in the order you removed them.
- Reusing old supply lines without checking them. Bulging or brittle hoses should be replaced.
Recommended Gear
- A basin wrench reaches the mounting nuts behind the sink, where a standard wrench cannot fit. View on Amazon
- Penetrating oil loosens seized threads and corroded nuts so they turn without force. View on Amazon
FAQ
Do I need to turn off the main water supply?
Not always. If the shutoff valves under the sink close fully and hold, you can work from there. If they are stiff, leaking or missing, turn off the main supply to the house.
Why won’t the mounting nut come loose?
Corrosion or mineral buildup is the usual cause. Apply penetrating oil, wait 15 to 20 minutes and work the nut back and forth in small turns.
Should I replace the supply lines when I remove the faucet?
It is a good idea if the lines look cracked, bulging or stiff. Replacing them while the cabinet is open saves a repeat job later. If you are unsure about water connections, consult a licensed plumber.
Conclusion
Shut off the water, disconnect the supply lines and loosen the mounting nuts, and the faucet will lift out cleanly. Take your time with corroded hardware and clean the sink deck before installing the replacement. With the old faucet removed, you are ready to set the new one in place.
Related reading
- Kitchen Sink Faucet Replacement: A Step-by-Step Guide (2026)
- Kitchen Sink Faucet Grohe: Models, Finishes and How to Choose (2026)
- Kitchen Sink Faucet Bronze: 7 Finishes and Buying Tips (2026)
- Kitchen Sink Faucet Black: Finishes, Care and Buying Tips
- Delta Leland Single-Handle Touch Kitchen Sink Faucet Review (2026)
- Choosing a Kitchen Faucet by How You Use Your Sink
