Updated November 2026
A Moen faucet that is leaking can usually be fixed in under an hour with basic hand tools. Most leaks come from one of a few worn parts: the cartridge, the O-rings, the spout seal or the aerator. This guide shows you how to narrow down the source, shut off the water safely and make the repair.
Find Where the Leak Is Coming From
Before you take anything apart, figure out where the water is escaping. A drip from the spout when the handle is off usually points to the cartridge. Water pooling around the base of the faucet suggests a loose mounting nut or a failed base gasket. Leaking from the handle or the side of the spout points to a worn O-ring or a damaged spout seal.
Dry the faucet completely, then watch it for a minute with the handle closed. Where the water first appears tells you which part to check.
Shut Off the Water and Prepare
Turn off the shutoff valves under the sink, one for hot and one for cold. Then open the faucet to drain the remaining water in the lines. Place a towel in the sink basin so small parts cannot wash down the drain.
- Close both supply valves under the sink.
- Open the faucet to relieve pressure and drain the lines.
- Gather a Phillips screwdriver, an Allen wrench, a flat-blade screwdriver, plumber’s grease and replacement parts.
- Take a photo of the faucet before disassembly so you can match the parts later.
Repair a Leak From the Spout or Handle
For a drip from the spout, the cartridge is the most likely cause. Remove the handle screw, lift off the handle and the cap, then remove the retaining clip. Pull the cartridge straight out using the stem as a grip. Moen cartridges rarely wear evenly, so replace it with a matching model rather than trying to clean it.
If water leaks from around the handle or the base of the spout, check the O-rings. Coat new O-rings lightly with plumber’s grease before reinstalling. Excess grease can clog the cartridge, so use only a thin film.
Check the Base and Mounting Nut
Water that pools at the base often means the mounting nut under the sink has worked loose. Tighten it by hand, then with a wrench, but avoid overtightening, which can crack plastic components. A failed base gasket needs replacement, and the faucet may need to be lifted to access it.
Common Mistakes to Avoid
- Skipping the supply shutoff, which leads to a soaked cabinet floor.
- Installing a cartridge that does not match your faucet’s model number.
- Using petroleum-based lubricants on rubber parts, which can cause swelling.
- Overtightening the handle screw or mounting nut.
- Reassembling without checking that the cartridge seats fully.
Recommended Gear
A basic cartridge puller helps you remove a stuck cartridge without damaging the valve body. View on Amazon
Silicone-based plumber’s grease is safe for most faucet seals and resists washing out. View on Amazon
If you also want to compare parts before ordering, see 6 Best Moen Leaking Kitchen Faucet Repair Parts (2026) and Replace Cartridge Moen Faucet: 6 Best Cartridges Compared (2026). For a dripping kitchen model specifically, Moen Kitchen Faucet Dripping: 6 Causes and How to Fix Each One covers additional causes.
FAQ
Why does my Moen faucet keep dripping after I replace the cartridge?
The new cartridge may not be seated fully, or the retaining clip may not be locked in place. Remove the handle and confirm the cartridge sits flush in the valve body.
Can I fix a Moen faucet leak without turning off the water?
You should not. Turning off the supply valves under the sink is the only way to prevent water from spraying during disassembly.
When should I call a plumber?
Call a professional if the valve body is cracked, if water comes from inside the wall, or if you cannot shut off the supply valves. Consult a licensed plumber for any work involving gas lines or structural repairs.
Conclusion
Most Moen faucet leaks trace back to a worn cartridge, O-ring or mounting nut. Identify the source, shut off the water and replace the faulty part with a matching model. A careful repair usually stops the drip for good.
