Updated November 2026

The installation of kitchen faucet work comes down to four jobs: shutting off the water, mounting the faucet body to the sink, connecting the supply lines and drain, and checking for leaks. With basic hand tools and about an hour of careful work, most homeowners can finish a single-hole or three-hole replacement without calling a plumber. This guide walks through each stage in the order you should do them.

Before You Start: Check Fit and Gather Tools

Measure the number of mounting holes in your sink deck first. Single-hole faucets need one opening, while widespread models often need three, and a faucet with a separate sprayer may need four. A faucet designed for a three-hole layout will not sit flat on a single-hole sink without a deck plate, so confirm the match before you remove anything.

Shopping for one? See our guide: Price to Install Kitchen Faucet: 6 Best Installation-Friendly Picks (2026).

Gather these tools and supplies:

  • Adjustable wrench and basin wrench
  • Plumber’s putty or silicone sealant (if the manufacturer calls for it)
  • Bucket and old towels
  • Flexible braided supply lines, sized to the faucet’s inlet threads
  • Flashlight and a helper for overhead access

Step-by-Step Faucet Mounting

Shut Off the Water and Remove the Old Faucet

Close the under-sink shutoff valves by turning them clockwise until they stop. Open the faucet to drain remaining water, then disconnect the supply lines with the basin wrench. Loosen the mounting nuts beneath the sink, and lift the old faucet out. Clean the sink surface so the new gasket or putty seats evenly.

Set the Faucet and Tighten Mounting Hardware

Place the new faucet over the holes, feeding the supply hoses and any sprayer lines through first. Apply a bead of plumber’s putty under the base if the instructions specify it, then secure the mounting nuts or plate from below. Tighten evenly, checking that the faucet stands straight. Overtightening can crack a porcelain or composite sink, so snug the hardware firmly and stop.

Connecting Supply Lines and Testing for Leaks

Attach the hot and cold supply lines to the shutoff valves, then connect the other ends to the faucet inlets. Hand-tighten first, then add a quarter turn with a wrench. Reopen the shutoffs slowly. Run the faucet on cold, then hot, and watch each joint for at least five minutes. A slow drip at a compression nut usually means it needs another eighth to quarter turn.

Common Mistakes to Avoid

  • Opening the shutoff valves fast, which can loosen connections and spray water under the cabinet.
  • Skipping the flush step, so debris clogs the aerator and reduces flow.
  • Using thread tape on compression fittings that are sealed with a washer.
  • Reusing old supply lines that show cracks or bulging.
  • Forgetting to check the drain assembly connection after the faucet is in.

A basin wrench reaches the mounting nuts tucked behind the sink and is hard to replace with a standard wrench. View on Amazon

Braided stainless steel supply lines resist kinking and are easier to route than rigid copper tubing. View on Amazon

FAQ

Do I need a plumber for faucet installation?

Most homeowners can handle a standard replacement with basic tools. If your shutoff valves are corroded or your sink has no mounting holes, a licensed plumber is the safer choice. Consult a professional if you find water damage under the sink.

How long does a kitchen faucet installation take?

A straightforward swap usually takes one to two hours, including cleanup and leak testing. Older sinks or stubborn nuts can add time.

Why does my new faucet drip after installation?

A loose compression nut or an unseated gasket is the usual cause. Tighten the connection a little more, and check that the supply lines are fully threaded before assuming the cartridge is faulty.

Conclusion

A careful installation of kitchen faucet work depends on checking fit, shutting off water properly and testing every joint before you close the cabinet. Take your time with the mounting nuts and supply connections, and you will avoid most callbacks. Once the faucet is running clean, you are done.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.