Updated November 2026
Removing a kitchen faucet takes most homeowners about an hour, and it comes down to three jobs: shutting off the water, disconnecting the supply lines, and loosening the mounting hardware under the sink. This guide walks through how to take out a kitchen faucet from start to finish, whether you are replacing it or just clearing the way for a repair.
Before You Start: Shut Off the Water
Locate the two shutoff valves under the sink, one for hot and one for cold. Turn them clockwise until they stop. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Then open the faucet to relieve any remaining pressure and let the lines drain into a bucket.
Shopping for one? See our guide: Top 7 Delta Kitchen Faucets with Pull-Out Spray for Everyday Use.
Disconnect the Supply Lines and Spray Hose
Place a towel and a bucket under the sink, since a small amount of water will still come out of the lines. Use an adjustable wrench or basin wrench to loosen the compression nuts on the hot and cold supply lines, then unscrew them by hand. If your faucet has a pull-out spray, disconnect the hose at the quick-connect coupling below the sink, and release the weight or counterweight that holds the hose in place.
Remove the Mounting Nuts and Lift the Faucet
Most faucets are held to the sink deck by one or more mounting nuts on threaded studs. Reach up under the sink with a basin wrench, which is built to grip nuts in tight spaces. Turn counterclockwise until the nut is free. Some faucets use a plastic mounting plate or a locknut rather than a stud. Once the hardware is off, lift the faucet straight up from the top of the sink. If it is stuck on old sealant, run a plastic putty knife around the base to break the seal before you pull.
Tools and Materials Checklist
- Adjustable wrench and basin wrench
- Bucket and towels
- Flashlight or headlamp
- Plastic putty knife
- Plumber’s tape and a small tube of plumber’s putty for reinstallation
- Replacement supply lines, if the old ones are corroded
Clean the Sink Deck Before Installing Anything New
With the old faucet out, scrape away old putty, sealant and mineral deposits from the holes. A clean, flat surface helps the new faucet seal properly. Inspect the supply shutoff valves at the same time. If either one drips when you open it or will not fully close, replace the valve before you reconnect anything, because it is much easier to do now than after the new faucet is in place.
Common Mistakes to Avoid
- Skipping the shutoff valves and getting soaked when the line is opened.
- Forcing a stuck nut without penetrating oil, which can strip threads or crack the sink.
- Losing track of the mounting hardware. Bag and label each piece as it comes off.
- Disconnecting the spray hose without noting how the counterweight is positioned.
- Taking photos before you start, so you can match the layout when installing the new faucet.
Recommended Gear
- A basin wrench helps you reach and turn mounting nuts that a standard wrench cannot access. View on Amazon
- Penetrating oil loosens corroded nuts and fittings that resist turning. View on Amazon
- A headlamp keeps both hands free while you work in the dark cabinet space under the sink. View on Amazon
FAQ
Do I need to remove the faucet to replace the sink?
Yes. The faucet mounts through the sink deck, so it must come out before the sink can be lifted or replaced.
What if the shutoff valves are seized?
Shut off the main water supply to the house and call a licensed plumber if the valves will not close. Forcing a seized valve can break it and cause a leak.
How long does removing a kitchen faucet take?
Most people finish in 30 to 60 minutes once the water is off, though rusted or sealed hardware can add time. Plan a bit longer if the faucet has been in place for many years.
Conclusion
To take out a kitchen faucet, shut off the water, disconnect the supply lines and spray hose, then remove the mounting nuts and lift the faucet away. Clean the sink deck and check the shutoff valves before installing a replacement. If anything looks corroded or you are unsure about the valves, consult a licensed plumber before you proceed.
