Updated November 2026
To take off a kitchen sink faucet, you shut off the water supply, disconnect the supply lines, release the mounting nuts underneath the sink, and lift the faucet out. Most standard faucets can be removed in under an hour with a few basic tools. The steps are similar across brands, though the mounting hardware can differ, so check your model before you start.
Before You Start: Shut Off the Water and Gather Tools
Turn off the water at the shutoff valves under the sink, one for hot and one for cold. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Then open the faucet to relieve pressure and let any remaining water drain into a bucket.
Shopping for one? See our guide: 5 Best Faucets for Kitchen Sink Options Compared for Every Need (2026).
Gather these tools before you begin:
- A flashlight or headlamp
- An adjustable wrench and a basin wrench
- A bucket and old towels
- Penetrating oil for rusted nuts
- A plastic putty knife or painter’s tape for protecting the finish
Step-by-Step: Removing the Faucet
- Disconnect the supply lines. Place the bucket under the connections and loosen the nuts joining the flexible supply lines to the shutoff valves. Hold the valve steady with a second wrench so it does not twist.
- Remove any spray hose and weight. If your faucet has a pull-out sprayer, detach the hose from its docking clip under the sink and unscrew the counterweight, if one is present.
- Access the mounting nuts. Reach under the sink and locate the mounting nuts or the plastic retaining nut that holds the faucet base to the sink deck. A basin wrench is the easiest tool for tight, hard-to-reach spots.
- Loosen the nuts. Turn them counterclockwise. If they are corroded, spray penetrating oil and wait about 10 minutes before trying again.
- Remove any mounting plate. Some faucets sit on a plate or gasket. Lift it off, noting its orientation.
- Lift the faucet out. Work from above while a helper or you steady the base from below. Pull straight up, guiding the supply lines through the holes.
- Clean the deck surface. Scrape away old gasket material and mineral buildup so the new faucet seats flat.
Checking Your Faucet Type Before You Pull
Single-hole faucets usually mount with a single large nut and may use a pivot ball. Three-hole and widespread models often use separate nuts for each handle and spout. Pull-down and touchless models add electrical or hose connections that must be unplugged or detached first. Taking a photo under the sink before you start makes reassembly much easier.
Common Mistakes to Avoid
- Skipping the water shutoff and getting soaked when the lines come loose.
- Forcing the mounting nuts without penetrating oil, which can crack plastic or strip threads.
- Letting the basin wrench slip and scratch the finish. Tape the deck or tool jaws to reduce marks.
- Forgetting that some supply lines are hard to reach once the faucet is partly loose.
- Failing to note the position of the gasket or plate, which can cause leaks when reinstalled.
Recommended Gear
- Basin wrench: Its long, angled jaws reach mounting nuts in the cramped space behind the sink. View on Amazon
- Penetrating oil: It loosens corroded nuts that would otherwise resist hand force. View on Amazon
- Headlamp: Hands-free light helps when you are working upside down under the cabinet. View on Amazon
FAQ
Do I need to turn off the main water supply?
Usually no, if the under-sink shutoff valves work properly. If they are stuck, leaking or missing, turn off the main house supply before disconnecting anything.
What if the mounting nuts will not budge?
Apply penetrating oil and wait at least 10 minutes. If they still resist, a basin wrench with steady pressure usually works, but stop if the nut begins to crack or deform.
Can I remove the faucet myself, or should I hire a plumber?
Most homeowners can remove a standard faucet with basic tools. If you find corroded pipes, damaged valves or water damage under the sink, consult a licensed plumber before continuing.
Conclusion
Removing a kitchen sink faucet comes down to shutting off the water, disconnecting the lines and releasing the mounting nuts. Take your time with stubborn hardware and photograph the setup beforehand. With those steps done, you can install a replacement or move on to repairs.
