Updated November 2026

To replace a cartridge in a Delta faucet, you shut off the water, remove the handle and retaining hardware, pull the old cartridge, and seat a matching replacement in the same orientation. Most homeowners can finish the job in under an hour with basic tools. A dripping, stiff or hard-to-control handle usually points to a worn cartridge, and swapping it is far cheaper than replacing the whole faucet.

Before You Start: Confirm You Have the Right Cartridge

Delta uses several cartridge types, and a part that looks similar can be the wrong size or connection style. Look for the model number stamped on the old cartridge or listed in your faucet’s installation guide. If the number is worn off, note the handle style and whether the faucet has one handle or two. For help matching parts, see Delta Faucet Cartridge Identification: How to Find the Right One (2026).

Shopping for one? See our guide: Replace Delta Faucet Stem: 7 Best Repair Kits Compared (2026).

How to Replace the Cartridge, Step by Step

Step 1: Shut off the water

Close the supply valves under the sink. If the valves are stuck, shut off the main water supply and open the faucet to drain remaining pressure.

Step 2: Remove the handle

Pry off the decorative cap on top of the handle with a flat-blade screwdriver or your fingernail. Loosen the handle screw with a Phillips or hex key, then lift the handle off. Some Delta models use a hidden set screw under the cap instead.

Step 3: Remove the retaining nut or clip

Under the handle you will find a bonnet nut or a metal retaining clip. Unscrew the nut with an adjustable wrench or the plastic wrench Delta often includes, or pull the clip free. Lift off the bonnet or escutcheon to expose the cartridge.

Step 4: Pull the old cartridge

Grip the cartridge stem and pull it straight up. If it’s stuck from mineral buildup, rock it gently side to side. Avoid pliers on the plastic body, which can crack it. A cartridge puller can help if it won’t budge.

Step 5: Install the new cartridge

Before inserting the new cartridge, check that the O-rings are seated and lightly coated with plumber’s grease. Align the cartridge’s tab or notch with the slot in the faucet body, which is what sets the hot and cold orientation. Push it down until it sits flush.

Step 6: Reassemble and test

Reinstall the retaining clip or nut, put the handle back on, and tighten the screw without overtightening. Turn the water back on slowly, run the faucet on hot and cold, and check for drips at the spout and base.

Checklist: Tools and Supplies

  1. Replacement cartridge matched to your Delta model
  2. Phillips or hex screwdriver and flat-blade screwdriver
  3. Adjustable wrench or Delta’s cartridge removal wrench
  4. Plumber’s silicone grease
  5. Old towel or rag to protect the finish
  6. Bucket or towel under the sink

Common Mistakes to Avoid

  • Installing the cartridge backward, which reverses hot and cold.
  • Skipping the grease, which can make the new O-rings tear or leak.
  • Using metal tools on the handle finish and leaving scratches.
  • Forgetting to shut off the water, which leads to a soaked cabinet.
  • Overtightening the handle screw, which can strip threads.
  • Silicone plumber’s grease keeps O-rings supple and helps the cartridge slide in smoothly. View on Amazon
  • Faucet cartridge puller gives you grip on a stuck cartridge without damaging the body. View on Amazon
  • Basic faucet repair kit bundles common O-rings and clips, useful if a small part is worn too. View on Amazon

FAQ

Do I need to turn off the water main to replace a Delta cartridge?

Usually no. Closing the two supply valves under the sink is enough for most kitchen and bathroom faucets. If those valves are stiff or leak, shut off the main supply instead.

Why is my faucet still dripping after I replaced the cartridge?

Check that the cartridge is fully seated and oriented correctly, and that the O-rings are not pinched. Debris in the valve seat can also cause a drip, so flush the supply lines before reassembling.

How long does a Delta cartridge last?

Lifespan depends on water hardness and use, and manufacturers do not publish a fixed number. Many owners replace cartridges when drips or stiffness appear, often after several years of regular use.

Conclusion

Replacing a Delta faucet cartridge comes down to shutting off the water, removing the handle and retainer, and seating a matched cartridge in the right orientation. With the right tools and a little grease, most people finish in under an hour. If you run into an unusual model or parts you can’t identify, consult a licensed plumber for help.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.