Updated November 2026
To repair an outdoor faucet handle, you will shut off the water supply, remove the handle and stem, and then replace the worn packing washer, O-ring or stem washer that is causing the trouble. Most handle problems come down to one of three parts, and a basic set of hand tools is usually enough. The whole job often takes less than an hour.
Identify the Problem Before You Start
Your symptoms point to the cause. A handle that spins freely without shutting off the water usually has a worn stem washer. A handle that feels loose or wobbles often has a loose retaining screw. Water leaking from around the stem, under the handle, is typically a failed packing washer or O-ring.
Shopping for one? See our guide: Bathroom Moen Faucet Repair: Lever Handle Kit Review (2026).
Turn the handle on and watch closely. If water drips from the spout after you close the handle, the problem is inside the valve. If water seeps out around the handle base, the packing or O-ring is the likely culprit.
Shut Off Water and Remove the Handle
Start by cutting the water supply. Most outdoor spigots have an interior shutoff valve, so find it and close it. Then open the outdoor faucet to drain any remaining water.
- Pry off the decorative cap on top of the handle with a flat-head screwdriver.
- Remove the handle screw with a Phillips or hex driver, depending on your model.
- Lift the handle straight up. If it is stuck, tap it gently with a rubber mallet rather than prying on it.
- Unscrew the packing nut or bonnet nut with an adjustable wrench. Turn counterclockwise.
- Pull out the stem assembly. Keep track of every part as you remove it.
Replace the Worn Parts
Check the stem washer at the bottom of the stem. It is usually a rubber disc held by a brass screw. If the rubber is cracked, flattened or pitted, replace it. Use the same size and shape so the seat closes fully.
Next, inspect the packing washer or O-ring on the stem. If it is hard, split or flattened, swap it out. Rub a thin coat of plumber’s grease on the new washer or O-ring before reinstalling. Dry rubber tears more easily and leaks sooner.
Reassemble and Test
Reverse the removal steps. Tighten the packing nut snugly, but do not crank it down hard, as overtightening can make the handle stiff. Reattach the handle and cap, then slowly turn the water back on at the shutoff valve.
Open and close the spigot several times. Watch for drips at the spout and leaks around the handle. A small amount of weeping from the packing nut can often be fixed by tightening it a quarter turn.
Common Mistakes
- Forgetting to shut off the interior valve, which causes a spray of water when the stem comes out.
- Using the wrong replacement washer size, which leaves the seat unable to seal.
- Overtightening the packing nut, which stiffens the handle and can crack the bonnet.
- Skipping lubrication on the O-ring, which shortens its life.
- Mixing up parts during disassembly. Lay them out in order on a towel.
Recommended Gear
- Plumber’s grease for faucet seals helps new rubber parts slide into place without tearing and keeps them flexible. View on Amazon
- Adjustable wrench set gives you a firm grip on the packing nut without marring the finish. View on Amazon
- Outdoor faucet washer assortment lets you match the stem washer and packing washer size on hand. View on Amazon
FAQ
Why does my outdoor faucet handle spin without turning off the water?
The stem washer is usually worn or loose. Replacing it typically restores a firm shutoff.
Do I need to replace the whole faucet to fix a loose handle?
No. Tightening the handle screw or replacing a worn packing washer usually solves the problem. Consider a full replacement only if the valve body is cracked.
Can I repair the handle while the faucet is still attached to the house?
Yes, as long as you shut off the interior valve first. Outdoor spigots are usually easy to work on in place. If the interior valve will not close fully, consult a licensed plumber.
Conclusion
Most outdoor faucet handle problems come down to a worn stem washer, packing washer or O-ring. Shut off the water, remove the stem, replace the damaged part and reassemble without overtightening. With the right parts and a little patience, your handle should turn smoothly and seal tight again.
