Updated November 2026

A leaking faucet handle is usually caused by a worn O-ring, a failed cartridge or a loose packing nut, and most of these can be fixed in under an hour with basic hand tools. This guide walks you through how to repair a faucet handle leak from start to finish: shutting off the water, identifying the source, disassembling the handle and replacing the worn parts. Follow the steps in order and you should have a dry handle by the end.

Identify Where the Leak Is Coming From

Before you take anything apart, figure out where the water is escaping. A drip from the spout means the problem is inside the valve body, while water seeping out around the base of the handle points to a packing or O-ring issue. Run the faucet briefly and watch closely. If water beads at the base of the handle, you are dealing with a stem seal. If the handle itself feels stiff or wobbly, check for a loose packing nut or cartridge retaining clip.

Shopping for one? See our guide: Bathroom Moen Faucet Repair: Lever Handle Kit Review (2026).

Shut Off the Water and Disassemble the Handle

Close the isolation valves under the sink, or the main shutoff if you have no local valves. Open the faucet to release any remaining pressure. Then work through these steps:

  1. Pry off the decorative cap on the handle with a flat-head screwdriver or a thin putty knife, wrapping the tip in tape to protect the finish.
  2. Remove the handle screw, usually a Phillips or Allen type, and lift the handle straight up.
  3. Unscrew the packing nut or bonnet nut with an adjustable wrench, wrapping the jaws in a rag to avoid scratches.
  4. Pull out the stem or cartridge. Note how each piece is oriented before you remove it, or photograph it with your phone.

Replace the Worn O-Rings, Packing or Cartridge

Most handle leaks come from one of three parts. Compression-style stems use rubber washers and an O-ring that flatten over time. Cartridge faucets rely on a single unit that should be replaced as a whole when it wears out. Ball-type faucets use rubber seats and springs. Take the worn part to a hardware store to match the size and shape exactly, because even a small difference will leak. Lubricate new O-rings with plumber’s silicone grease, not petroleum-based products, which can degrade rubber. Reinstall the stem or cartridge in the original orientation, then tighten the packing nut just until snug. Overtightening is a common cause of stiff handles and new leaks.

Reassemble and Test the Faucet

Reverse the disassembly steps, reattaching the handle, the screw and the decorative cap. Slowly reopen the isolation valves and check for leaks around the handle before you run the water at full pressure. Cycle the handle through its full range several times. If you still see seepage, shut the water off again and check whether the O-ring seated correctly.

Tools You Will Need

  • Adjustable wrench and flat-head screwdriver
  • Phillips or Allen screwdriver, depending on the handle screw
  • Replacement O-rings or cartridge matched to your faucet brand
  • Plumber’s silicone grease and a clean rag

Common Mistakes

  • Skipping the shutoff step, which leads to a sudden spray of water.
  • Buying generic O-rings without measuring the old ones first.
  • Using petroleum-based lubricants that break down rubber.
  • Overtightening the packing nut, which causes stiff handles and early wear.
  • Forgetting to note the orientation of the stem or cartridge before removal.

A basic faucet repair kit that includes assorted O-rings and washers can save a second trip to the store when you do not know the exact size. Plumber’s silicone grease is the right lubricant for rubber seals and is worth keeping on hand. A small set of Allen and Phillips screwdrivers helps when a handle screw is hidden under a cap. View on Amazon View on Amazon

FAQ

Do I need to replace the whole faucet to stop a handle leak?

Usually not. Most handle leaks are caused by worn O-rings, washers or a cartridge, and replacing those parts is far cheaper than a new faucet.

How do I know if I need a new cartridge or just an O-ring?

If the leak persists after replacing the O-rings and the handle feels loose or gritty, the cartridge is likely worn. Cartridges are typically replaced as a single unit.

When should I call a plumber?

If the water shutoff valves under the sink do not close fully or the leak continues after several repair attempts, consult a licensed plumber to avoid water damage.

Conclusion

Fixing a faucet handle leak comes down to shutting off the water, identifying the worn part and replacing it with an exact match. Take your time during disassembly and keep track of how each piece fits. With the right parts and a little patience, most handle leaks stop for good in a single afternoon.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.