Updated November 2026
To repair a dripping tub faucet, you shut off the water supply, remove the handle and trim, identify whether the faucet uses a washer or a cartridge, and replace the worn part. Most drips come from a worn washer, an O-ring or a failing cartridge, and the whole job usually takes an hour or two with basic hand tools. The steps below work for most two-handle and single-handle tub faucets.
Shut Off the Water and Gather Your Tools
Close the hot and cold shutoff valves under the tub or at the main line. Then open the tub faucet to drain any remaining water and relieve pressure. Place a towel over the drain to catch small parts, since a dropped screw can disappear quickly.
Shopping for one? See our guide: 6 Best Tub Faucet Repair Kits for Leaks and Drips (2026).
- Phillips and flathead screwdrivers
- Adjustable wrench or basin wrench
- Replacement washers, O-rings or cartridge matched to your brand
- Plumber’s grease and a small rag
Remove the Handle and Access the Valve Stem
Pry off the decorative cap on the handle, then remove the screw underneath. Lift the handle straight up. If it sticks, a little penetrating oil and gentle wiggling usually frees it. Next, unscrew the stem or cartridge retaining nut, which often requires a wrench wrapped in a rag to protect the finish.
Identify the Faucet Type and Replace the Worn Part
Compression faucets use a rubber washer at the bottom of the stem. Remove the screw holding the washer, take the old one to a hardware store for an exact match, and install the new washer with a dab of plumber’s grease. Cartridge faucets, common in single-handle designs, use a sealed cylinder that you pull straight out. Replacing the whole cartridge is usually more reliable than trying to repair its internal seals.
Brand matters here. Delta, Moen, Kohler and Pfister all use different cartridges and stems, so look for a stamp or model number on the old part, or check the manufacturer’s website before buying parts.
Reassemble and Test the Faucet
Reverse the disassembly steps, tightening the retaining nut snugly without forcing it. Reinstall the handle, turn the water back on slowly and check for drips with the faucet closed. Run both hot and cold to confirm the valve seats fully. If the drip continues, the valve seat inside the body may be pitted, which is a more involved repair.
Common Mistakes
- Forgetting to shut off both hot and cold supply valves before starting.
- Buying a washer that is slightly the wrong size, which causes continued leaking.
- Overtightening the retaining nut, which can crack the stem or cartridge.
- Skipping plumber’s grease, which lets the new washer wear out faster.
- Scratching the finish with pliers; wrap the jaws in tape or a rag.
Recommended Gear
- Plumber’s grease keeps rubber washers and O-rings supple and helps them seal. View on Amazon
- Basin wrench reaches retaining nuts in tight spaces behind a tub. View on Amazon
- Assorted faucet washer kit covers common sizes so you can match the old part by trial fit. View on Amazon
FAQ
Why does my tub faucet keep dripping after I replace the washer?
The new washer may be the wrong size or the valve seat may be worn or pitted. Check the washer fit first, then inspect the seat for roughness or mineral buildup.
Can I repair a tub faucet without shutting off the main water?
You can often close only the local shutoff valves under the tub, but if they are old or leak, shut off the main supply. Consult a licensed plumber if valves won’t close fully.
How do I know if I need a new cartridge or just a new washer?
If the faucet has a single handle or a sealed cylinder, the cartridge is usually the failing part. Compression faucets with separate hot and cold handles typically need washers.
Conclusion
A dripping tub faucet is usually a worn washer, O-ring or cartridge, and replacing it is a manageable weekend task. Shut off the water, identify your faucet type and match the part carefully. Consult a professional plumber if the valve body itself is damaged.
