Updated November 2026
Learning how to fix a dripping faucet in the kitchen usually comes down to one job: finding the worn part that lets water slip past and replacing it. In most cases you can finish the repair in under an hour with a few basic tools. This guide covers the shutoff, the disassembly, the parts to check and the reassembly for the most common kitchen faucet designs.
Before You Start: Shut Off the Water and Identify Your Faucet
Close the hot and cold shutoff valves under the sink, then open the faucet briefly to drain the lines. Place a towel in the sink basin so small parts cannot wash down the drain if they slip. Next, identify the faucet type, since it determines which part you need to replace. Single-handle faucets usually use a cartridge, while two-handle models often use compression stems with rubber washers.
Shopping for one? See our guide: Fix Moen Kitchen Faucet: 5 Best Repair Parts Compared (2026).
How to Fix a Dripping Kitchen Faucet Step by Step
- Pry off the decorative cap on the handle and remove the handle screw with a Phillips or hex key.
- Lift the handle off and unscrew the bonnet nut or retaining clip that holds the cartridge or stem in place.
- Pull out the cartridge or stem. Compare it to your replacement part to confirm the size and shape match.
- Install the new cartridge or washer, making sure the seals sit flush and the stem orientation matches the original.
- Reassemble in reverse order, turn the water back on slowly and test the faucet at both hot and cold settings.
Check the Parts That Commonly Cause Drips
A drip is rarely caused by the spout itself. Worn cartridges and compression washers are the usual culprits, but the valve seat inside the faucet body can also be pitted by mineral buildup. Manufacturers often specify replacing the O-rings whenever you open the faucet, because they are inexpensive and stiffen with age. Look for grit, white mineral crust or cracked rubber on each part before reinstalling it.
| Faucet Type | Likely Drip Source | Typical Fix |
|---|---|---|
| Single-handle cartridge | Worn cartridge or O-rings | Replace the cartridge |
| Two-handle compression | Worn rubber washer or seat | Replace the washer and seat |
| Ball-type | Worn ball, springs or seats | Replace the internal kit |
If your leak is coming from the base or the spout rather than the spout opening, the cause is different. Our guide to Moen Kitchen Faucet Dripping: 6 Causes and How to Fix Each One covers those cases in more detail, and How to Fix a Leaky Kitchen Faucet: 5 Steps for Most Models is useful if the water is leaking from somewhere other than the spout.
Tools and Supplies You May Need
- Screwdrivers (Phillips and flat-head) and an Allen or hex key set
- Adjustable wrench or basin wrench
- Replacement cartridge, washers or O-rings matched to your brand
- Plumber’s grease and a rag or towel
Recommended Gear
- Plumber’s silicone grease: Helps O-rings slide into place without tearing and keeps them sealing longer. View on Amazon
- Faucet cartridge puller: Helps lift a stuck cartridge without damaging the faucet body. View on Amazon
Common Mistakes
- Reinstalling a cartridge with the wrong orientation, which keeps the drip going.
- Forgetting to close the shutoff valves before disassembly.
- Overtightening the handle screw, which can crack the cartridge housing.
- Buying a replacement part without matching the brand and model number.
- Skipping the O-ring replacement when the cartridge is already out.
For brand-specific steps, see How to Replace a Delta Kitchen Faucet Cartridge in 6 Steps (2026) or How to Repair a Leaky Moen Faucet: Step-by-Step Fix for Drips and Leaks. If you are unsure which part fits your faucet, Moen Kitchen Faucet Parts Diagram: How to Find and Use Yours shows how to locate the right model reference.
FAQ
Do I need to turn off the water main to fix a dripping kitchen faucet?
Usually no. Closing the hot and cold shutoff valves under the sink is enough for most kitchen faucets. If those valves are stuck or leak, you may need to shut off the main supply.
How long does it take to fix a dripping kitchen faucet?
Most repairs take 30 to 60 minutes once you have the correct replacement part. Unexpected corrosion or a stuck cartridge can add time.
Can I fix the drip without replacing the cartridge?
Sometimes. Replacing worn O-rings or a washer may stop the leak if the cartridge body is still in good shape. If the drip continues, replace the cartridge.
Conclusion
Fixing a dripping kitchen faucet is a manageable job when you shut off the water, identify the faucet type and replace the worn part. Match the replacement to your brand and model, and always install new O-rings. If the drip returns or you find damage to the faucet body, consult a licensed plumber.
