Updated November 2026

Fixing a Delta faucet leak usually comes down to one of three parts: a worn cartridge, a failing O-ring or seal, or a loose spout. In most cases you can complete the repair in under an hour with a screwdriver, an Allen wrench and a replacement part. This guide shows you how to find the source of the leak and fix it correctly.

Find Where the Leak Is Coming From

Before you take anything apart, figure out which part is leaking. A drip from the spout that continues when the handle is off almost always means the cartridge is worn. Water leaking at the base of the spout or around the handle points to a worn O-ring or a loose spout connection. Dripping from under the sink usually means a supply line or connection nut has failed.

Shopping for one? See our guide: 7 Best Repair Delta Bathtub Faucet Parts and Kits for Leaks (2026).

Turn the handle on and off a few times and watch closely. If the leak changes with handle position, the cartridge is the likely culprit.

Shut Off the Water and Prepare the Faucet

Close the shutoff valves under the sink. If the valves are stiff or do not close fully, shut off the main water supply to the house. Then open the faucet to drain any water left in the lines.

  1. Place a towel in the sink basin to protect the finish and to catch any small parts.
  2. Pry off the decorative handle cap, usually with a flat screwdriver wrapped in tape.
  3. Remove the handle screw, then lift the handle straight off.
  4. Unscrew the cap nut and pull out the cartridge.

Replace the Cartridge or Seals

Delta faucets use a cartridge that controls both temperature and flow. If the leak is coming from the spout and the cartridge looks worn, replacing the cartridge is the most reliable fix. Match the new cartridge to your exact Delta model number, which is typically printed on the faucet body or in the installation manual.

If the leak is at the base of the spout or handle, replace the O-rings instead. Clean the cartridge stem and the seating area before installing new rings. Apply a thin coat of plumber’s grease to the new O-rings so they seat without tearing.

Reassembling the Faucet

Seat the new cartridge with its alignment tab facing the correct direction, then tighten the cap nut snugly. Do not overtighten it, or you may crack the plastic parts. Reattach the handle, replace the screw and snap the decorative cap back into place.

Test the Repair

Slowly open the shutoff valves and check every connection for leaks. Run the faucet on hot and cold, then turn it off and watch the spout for at least a minute. If the drip continues, the cartridge may be seated incorrectly or the part may be the wrong model.

  • Plumber’s grease helps O-rings slide into place without tearing and keeps them sealed over time. View on Amazon
  • Delta-compatible cartridge is the most reliable fix for a drip that continues with the handle off. View on Amazon
  • Allen wrench set covers the hex screws found on many Delta handles and cartridges. View on Amazon

Common Mistakes to Avoid

  • Replacing the cartridge without confirming the model number, which leads to a part that does not fit.
  • Skipping the shutoff valves and getting soaked when the handle comes off.
  • Overtightening the cap nut, which can crack the cartridge housing.
  • Forgetting to lubricate new O-rings, causing them to tear during installation.
  • Assuming a leak under the sink is a faucet problem when a supply line may be at fault.

For more detail on the specific steps, see Replacing a Delta Faucet Cartridge: A Step-by-Step Guide (2026) and Replacing a Delta Faucet Stem: Step-by-Step Fix for Drips (2026). If your leak is in a tub faucet, How to Fix a Delta Tub Faucet Leak: 6 Steps to Stop Drips (2026) covers those valves specifically.

FAQ

Why does my Delta faucet keep dripping after I replace the washer?

Most newer Delta faucets use cartridges rather than washers, so a washer swap rarely solves the problem. Check whether you have a cartridge model and replace the cartridge instead.

How do I find the right replacement part for my Delta faucet?

Look for the model number printed on the faucet body or in the original packaging. Delta’s website and the installation manual list the matching cartridge and O-ring sizes.

When should I call a plumber?

Call a licensed plumber if the leak continues after a cartridge replacement, if the supply lines or shutoff valves are corroded, or if water is leaking inside a wall. Those problems can cause hidden water damage.

Conclusion

Fixing a Delta faucet leak starts with finding the source, whether that is the cartridge, an O-ring or a supply connection. Shut off the water, replace the faulty part with a matching one, and test the faucet carefully before calling the job done. With the right part and a little patience, most leaks can be stopped in a single afternoon.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.