Updated November 2026
Fixing a Delta faucet drip usually comes down to one worn part: the cartridge in a single-handle kitchen faucet or the stem in a two-handle model. In most cases you can shut the water off, pull the handle assembly, replace the failed part and reassemble the faucet in under an hour with basic hand tools. The steps below show you how to identify the source of the leak and fix it.
Identify Where the Drip Is Coming From
Before you take anything apart, confirm that the water is leaking from the spout and not from the base or handle. A constant drip from the spout almost always points to a worn internal seal or valve. Leaking around the base or handle points to different parts, usually O-rings or the escutcheon seal. Turn the faucet fully off and watch for a few minutes. If water continues to exit the spout, you have a valve problem.
Shopping for one? See our guide: 6 Best Delta Faucet Replacement Parts (2026): Expert Picks.
Shut Off the Water and Prepare the Work Area
Turn off the shutoff valves under the sink, then open the faucet to drain the remaining water. Place a towel in the basin to protect the finish and keep small parts from going down the drain. Plug the sink drain, since a dropped screw can disappear quickly.
- Close both supply valves under the sink fully clockwise.
- Open the faucet to relieve pressure and drain the lines.
- Lay a towel in the sink and stopper the drain.
- Gather a Phillips screwdriver, an Allen wrench, a flathead screwdriver and a replacement part.
Replace the Cartridge or Stem
Single-handle faucets
Remove the decorative cap and the handle screw, usually hidden under a small plastic cover. Lift the handle off, then unscrew the retaining nut or clip holding the cartridge. Pull the cartridge straight up. Delta cartridges are model-specific, so bring the old one to the store or match the number stamped on it. Install the new cartridge with the same orientation, reattach the retainer and handle, and check that the handle moves smoothly.
Two-handle faucets
Close the handle, remove the screw and handle, then unscrew the packing nut. Use a stem puller or an adjustable wrench to remove the stem. Replace the stem, its O-rings and the seat washer if it looks pitted. Reassemble in reverse order and tighten the packing nut only until it stops leaking around the handle.
Reassemble, Restore Water and Test
Lubricate new O-rings with plumber’s silicone grease before installation, since dry rubber tears easily. Reattach the handle, slowly open the supply valves and run the faucet for a minute to flush debris. Then turn the faucet off and check the spout after 15 minutes. A small drop is normal for a new cartridge settling in, but a steady drip means the part is seated incorrectly or the wrong replacement was used.
Common Mistakes
- Buying a generic cartridge without matching the Delta model number.
- Overtightening the handle screw, which can crack the plastic handle.
- Skipping the O-rings, which often leak even when the cartridge is new.
- Opening the supply valves too fast, which can dislodge the new part.
- Forgetting to plug the drain, which lets small screws escape.
Recommended Gear
- Plumber’s silicone grease helps seal and protect rubber O-rings during reassembly. View on Amazon
- Stem puller set makes it easier to remove a stuck stem from two-handle faucets. View on Amazon
- Basin wrench reaches the supply nut and mounting hardware in tight spaces under the sink. View on Amazon
FAQ
Why does my Delta faucet keep dripping after I replace the cartridge?
The cartridge may not be fully seated, or debris may be caught in the valve. Remove it, rinse the body and reinstall, checking the orientation and retainer.
Can I fix a drip without removing the handle?
Generally no, because the cartridge or stem sits behind the handle assembly. Some models allow limited adjustment of the packing nut, but this rarely stops a valve drip.
How do I know which Delta repair part to buy?
Check the model number on the faucet body or the packaging and match it to the replacement part. If you are unsure, take the old cartridge or stem with you when shopping.
Conclusion
A Delta faucet drip is usually caused by a worn cartridge or stem, and replacing that part solves it in most cases. Shut the water off, identify the failed component, and reassemble carefully with lubricated O-rings. If the drip continues or water damage has already occurred, consult a licensed plumber.
