Updated November 2026

A Delta Cassidy widespread faucet uses three separate holes on the sink deck, with a spout in the center and two handles on either side. This guide walks you through identifying the model, installing it, and handling the most common fixes, such as a dripping spout, stiff handles or uneven hot and cold flow. Most of these jobs need only basic hand tools and about an hour if the supply lines are already in place.

Confirm Your Cassidy Model and Gather Tools

Before you start, check that the faucet is a widespread style. Widespread faucets have handles and spout on separate bases, which is different from a centerset faucet where all parts share one plate. Delta Cassidy models are typically sold for 8-inch spread sinks, so measure the distance between the centers of the two supply holes to confirm.

You will need:

  • Adjustable wrench and basin wrench
  • Phillips and flat-head screwdrivers
  • Plumber’s putty or silicone sealant rated for sinks
  • Allen wrench set (for handle set screws)
  • Bucket and old towels
  • Replacement cartridge or O-ring kit, if you are repairing rather than installing

Install the Faucet Step by Step

  1. Shut off both supply valves under the sink and open the faucet to drain residual water.
  2. Remove the old faucet or cover plate, then clean the deck around each hole.
  3. Seat the base gaskets onto the spout and handle bases. Set the spout in the center hole first.
  4. Thread the supply lines through the holes and connect them to the valves. Hand-tighten, then add a quarter turn with a wrench.
  5. Secure each base from below with the mounting nuts. Keep the bases level and aligned before the final tightening.
  6. Attach the handles, tighten the set screws, and install the decorative caps.
  7. Turn the supply valves on slowly and check every connection for drips.

Check Alignment Before Tightening

Tighten the mounting nuts evenly in small increments. Over-tightening one side can crack the base or shift the handle out of line, so work in quarter turns and recheck the level after each pass.

Fix a Dripping or Stiff Handle

Most Cassidy drips come from a worn cartridge or a loose handle that is pressing on the stem. Start by removing the handle cap and set screw, then pull the handle straight off. If the handle moves freely but water still leaks at the spout, the cartridge is the likely cause. Replace the cartridge with a model matched to the Delta series, and lubricate the new O-rings with plumber’s grease before reinstalling.

If the handle is stiff rather than leaking, look for mineral buildup around the stem. Soaking the cartridge in white vinegar for an hour often clears light scale. Heavy deposits usually mean the cartridge should be replaced.

Balance Hot and Cold Water Flow

If hot and cold water are uneven or one side runs weak, check the aerator on the spout first, since clogged screens cause most pressure complaints. Unscrew the aerator, rinse out debris, and reinstall it. If the problem persists, the supply valves under the sink may be partly closed or the water heater may need attention.

For a deeper look at related repairs, see Touch Faucet Delta Problems: 6 Common Causes and Easy Fixes and How to Install Delta Faucet Cartridge: A Step-by-Step Guide (2026). If you are comparing styles before buying, Delta Nicoli Widespread Faucet Review: Features and Performance shows how another widespread model handles everyday use.

Common Mistakes to Avoid

  • Forgetting to shut off the supply valves before disconnecting lines, which leads to spray and a messy cleanup.
  • Using too much sealant under the bases, which can squeeze into the handle mechanism.
  • Overtightening the spout nut, which can crack the mounting base.
  • Replacing the cartridge without checking the handle set screw, causing a loose handle to appear as a leak.
  • Skipping a test run after installation, which hides slow drips until they soak the cabinet.
  • Basin wrench: reaches the mounting nuts under the sink, where a standard wrench cannot fit. View on Amazon
  • Plumber’s grease: keeps cartridge O-rings sealed and moving smoothly during repairs. View on Amazon
  • Allen wrench set: fits the handle set screws that hold most Delta handles in place. View on Amazon

FAQ

Can I install a Delta Cassidy widespread faucet myself?

Yes, if the sink already has three holes and working supply lines. Plan on a few hours and keep a basin wrench handy, since the mounting nuts are hard to reach without one. Consult a licensed plumber if the supply lines need replacing.

Why is my Cassidy faucet dripping from the spout?

A worn cartridge is the most common cause. Remove the handle, inspect the cartridge, and replace it if the O-rings are cracked or the seat is damaged.

How often should I replace the cartridge?

There is no fixed schedule, since it depends on water quality and use. Replace it when you notice persistent drips, stiff handles or inconsistent temperature.

Conclusion

A Delta Cassidy widespread faucet is manageable for most homeowners with basic tools and careful alignment. Work through installation in order, check the cartridge first when leaks appear, and clean the aerator before assuming a larger problem. With these steps, you should have a steady, leak-free faucet that is easy to maintain.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.