Updated November 2026
The Delta faucet cartridge RP50587 is a replacement valve cartridge used in certain Delta faucets. If your faucet drips, sticks or delivers water at the wrong temperature, swapping this cartridge is often the fix. This guide explains how to confirm the part fits your faucet, how to remove the old cartridge and how to install the new one without introducing leaks.
Confirm the RP50587 Is the Right Cartridge
Delta cartridges are not interchangeable across all faucet families, so verify the part before you buy or start disassembly. Look for the number stamped on the old cartridge body or check the number printed on the packaging. You can also match it against the Delta model number, usually found on the faucet spout, under the sink or in the original manual. For help narrowing down the correct part, see Delta Faucet Cartridge Identification: How to Find the Right One (2026).
Shopping for one? See our guide: Delta Faucet Valve Cartridge Review: Features and Performance.
Keep in mind that some Delta single-handle faucets use a different cartridge for hot and cold control, and a few older models use a ceramic disc design instead. If the number does not match, do not force the part. Contact Delta customer service or a licensed plumber to confirm compatibility.
Tools and Preparation
Gather everything before you shut off the water. Most cartridge swaps take between 30 and 60 minutes, and having the right tools on hand keeps the job from stalling halfway through.
- Replacement RP50587 cartridge, with O-rings if included
- Adjustable wrench or the tool recommended by your faucet manual
- Phillips and flathead screwdrivers
- Plumber’s grease (silicone-based)
- Clean rags and a small dish for screws
- Bucket or towel to catch residual water
Shut off the hot and cold supply valves under the sink, then open the faucet to relieve pressure. Plug the drain so small parts do not disappear.
Step-by-Step Cartridge Replacement
- Remove the handle. Most Delta handles have a set screw hidden under a small cap or behind the handle base. Remove the cap, loosen the screw and lift the handle straight up.
- Remove the bonnet nut or retaining clip. Unscrew the cap nut or pop out the retaining clip that holds the cartridge in place. Some models use a cam assembly, so note how it sits before removing it.
- Pull out the old cartridge. Grip the stem firmly and lift it straight out. If it is stuck, work it gently side to side rather than prying hard, which can crack the faucet body.
- Compare the old and new parts. Line them up side by side to confirm the height, stem design and notches match.
- Lubricate the new cartridge. Apply a thin layer of plumber’s grease to the O-rings. Too much grease can attract debris, so use just enough to create a smooth seal.
- Install the new RP50587. Seat it in the same orientation as the old cartridge, aligning any index tabs with the faucet body slots. Press it down evenly.
- Reassemble and test. Replace the retaining clip or nut, reattach the handle and tighten the set screw. Turn the water back on slowly and check for leaks at the base and spout.
Troubleshooting After Installation
If water still leaks from the spout after reassembly, the cartridge may not be fully seated or an O-ring may be pinched. Remove the cartridge, check the O-rings for nicks and reinstall. If hot and cold are reversed, the cartridge was likely installed with the wrong orientation. Some homeowners report that a small amount of sediment in the supply lines can cause a new cartridge to stick, so flushing the aerator and checking the inlet screens can help.
Recommended gear
- Plumber’s grease: A silicone-based grease keeps the O-rings flexible and reduces friction during installation. View on Amazon
- Basin wrench: Useful if you need to reach the supply nuts or mounting hardware in a tight cabinet. View on Amazon
- O-ring pick set: Helps remove old O-rings without scratching the faucet body. View on Amazon
Tips and Common Mistakes
- Do not skip shutting off the water supply. Even with the valves closed, residual pressure can spray water when you pull the cartridge.
- Avoid using petroleum jelly, which can degrade rubber seals over time.
- Take a photo of the disassembly before you start so you can match the orientation later.
- If the spout still drips after a cartridge swap, check the valve seat for mineral buildup before buying another part. For related fixes, see Delta Faucet Valve Cartridge Replacement: 3 Best Picks Compared.
- Consult a licensed plumber if the faucet body is cracked or corroded, since replacing the cartridge will not solve those problems.
FAQ
Will the RP50587 fit every Delta faucet?
No. Delta uses many cartridge types, so check the number on your old part or the faucet model before buying. If the numbers do not match, the cartridge will not seat correctly.
Do I need to replace the whole faucet?
Usually not. A worn or failed cartridge is one of the most common causes of drips and temperature problems, and replacing it restores normal function in most cases.
What if the new cartridge still leaks?
Check that the O-rings are seated, the cartridge is oriented correctly and the handle is fully reattached. If leaks continue, consult a licensed plumber to inspect the valve body.
Conclusion
Replacing the Delta faucet cartridge RP50587 is a manageable repair when you confirm compatibility and work carefully. Shut off the water, note the orientation and lubricate the O-rings before seating the new part. With those steps done, most drips and temperature issues should be resolved.
