Updated November 2026
Learning how to repair a leaky sink faucet usually takes less than an hour and a basic set of tools. Most drips come from one worn part: a cartridge, a valve seat, a washer or an O-ring. This guide shows you how to identify the leak, shut off the water, swap the failing part and test your work.
Identify Where the Leak Is Coming From
Before you take anything apart, figure out where the water is escaping. A faucet that drips from the spout after you shut it off almost always has a worn cartridge or valve seat. Water seeping from around the base of the handle or the spout body usually points to a failing O-ring or packing nut. Leaks from under the sink suggest a supply line or connection problem, which is a different job.
Shopping for one? See our guide: 5 Best Leaky Faucet Repair Bathtub Kits for Common Leaks and Drips (2026).
Also note the faucet type. Single-handle faucets typically use a single cartridge, while two-handle faucets use separate stems or cartridges for hot and cold. Knowing this determines which parts you need.
Shut Off the Water and Remove the Handle
Close the shutoff valves under the sink, then open the faucet to drain the remaining water. Place a towel in the basin to protect the finish and to keep small screws from disappearing down the drain.
- Pry off the decorative cap on the handle with a flat-head screwdriver or a thin putty knife.
- Remove the handle screw with a Phillips or hex key, depending on the brand.
- Lift the handle off and unscrew the bonnet nut or retaining clip that holds the cartridge in place.
- Pull out the cartridge or stem. Take it with you to the store so you can match it exactly.
Replace the Worn Cartridge, Washers or O-Rings
Once the cartridge is out, inspect it. Look for grit, mineral buildup, cracks or damaged rubber seals. If the cartridge body looks intact, you may only need new O-rings and a seal kit. Many manufacturers, including Delta and Moen, sell replacement cartridges matched to specific models, so checking the model number on the faucet body saves time.
Clean the valve seat with a cloth or a seat wrench if your faucet has one. Rough or pitted seats can cause a leak even with a new cartridge. Lightly coat new O-rings with plumber’s grease before reinstalling. Avoid petroleum-based lubricants, which can degrade rubber.
Reassemble, Test and Check for Leaks
Reinstall the cartridge with the alignment tab or notch facing the correct direction, then reverse the steps you used to remove it. Tighten nuts snugly but do not overtighten, since this can crack plastic components or strip threads. Turn the shutoff valves back on slowly and check for leaks at every connection.
Run the faucet on both hot and cold and then shut it off. Wait a minute and check the spout. A drip-free faucet is the goal. If it still drips, the seat may need resurfacing or the cartridge may be the wrong part.
Common Mistakes
- Skipping the shutoff valves and getting soaked when the handle comes off.
- Buying a cartridge based on the faucet brand alone instead of the exact model number.
- Overtightening the bonnet nut, which can crack the body.
- Forgetting to note the orientation of the cartridge before removal.
- Ignoring a worn valve seat and replacing only the cartridge.
Recommended Gear
- Plumber’s grease helps seal and lubricate new O-rings without degrading the rubber. View on Amazon
- A faucet seat wrench set lets you clean or replace worn valve seats that a cartridge swap alone won’t fix. View on Amazon
- A faucet cartridge puller makes it easier to remove a stuck cartridge without damaging the body. View on Amazon
FAQ
Do I need to replace the whole faucet to fix a leak?
Usually not. Most leaks come from a worn cartridge, washer or O-ring, which costs far less to replace than the entire fixture.
Why does my faucet still drip after I replaced the cartridge?
The valve seat may be pitted or the cartridge may not match your faucet model. Inspect the seat and confirm the part number before reinstalling.
Should I hire a plumber for this repair?
Most homeowners can handle a cartridge swap with basic tools. If the shutoff valves won’t close fully or the supply pipes show corrosion or damage, consult a licensed plumber before proceeding.
Conclusion
Repairing a leaky sink faucet comes down to finding the failing part, shutting off the water and replacing the right component. Take the old cartridge with you when shopping, and check your work for leaks before calling the job finished. With patience and the right part, most drips can be stopped in a single afternoon.
