Updated November 2026
Most leaking sink faucets can be repaired in an afternoon with a screwdriver, an adjustable wrench and a replacement part. This guide shows you how to repair a leaking sink faucet by first finding where the water is escaping, then replacing the worn component, and finally testing the fix. The steps apply to most single-handle and two-handle kitchen and bathroom faucets.
Find Out Where the Leak Is Coming From
A faucet can leak in three places, and each one has a different fix. A drip from the spout means the valve or cartridge inside the faucet is worn or not sealing. Water leaking from the base of the handle usually points to a worn O-ring or packing nut. Water pooling under the sink or around the base of the faucet often means a loose mounting nut or a failed supply line connection.
Shopping for one? See our guide: Moen Sink Faucet Repair: 5 Best Kits and Parts Compared (2026).
Turn the water off at the shutoff valves under the sink before you touch anything. Then turn the faucet on briefly to drain any remaining water and confirm the flow has stopped.
Gather the Tools and Parts You Need
- Phillips and flathead screwdrivers
- Adjustable wrench and basin wrench
- Plumber’s grease and a soft cloth
- The correct replacement cartridge, O-rings or washers, matched to your faucet brand and model
- A small bowl or tray for holding screws
Model numbers are usually stamped on the faucet body or listed in the owner’s manual. Bring the old part to the store or photograph it before buying a replacement. Brands such as Delta, Moen and Kohler use different cartridge designs, so a generic part often won’t seal correctly.
Replace the Cartridge or Valve Stem
Most drips at the spout come from a worn cartridge. Remove the decorative cap and handle screw, then lift the handle off. Unscrew the retaining nut or clip holding the cartridge, and pull the cartridge straight out. Note its orientation, since a cartridge installed backward will leak.
Before inserting the new cartridge, coat the O-rings with plumber’s grease. Seat it fully, reattach the retaining clip, put the handle back on and tighten the screw. Some Moen and Delta models use a stainless steel clip that must be pressed in firmly to lock the cartridge in place. A leak that continues after replacement often means the cartridge was not fully seated.
Fix Leaks at the Base and Handle
If water seeps from around the handle or base, the O-rings or packing nut are the likely cause. Tighten the packing nut slightly, about a quarter turn at a time, but avoid overtightening, which can crack the seal or make the handle stiff. If tightening does not stop the leak, replace the O-rings and the packing washer.
When the faucet is still leaking under the sink after these repairs, check the supply line connections and the mounting nut underneath the sink. A basin wrench reaches the nut that a regular wrench cannot. Hand-tighten the connections first, then add a small additional turn with the wrench.
Test the Repair
Turn the water supply back on slowly. Run the faucet at full flow and at a low flow setting, then shut it off and watch the spout for at least a minute. A faucet that is holding properly will show no drips. Check the base and supply connections for moisture as well.
Common Mistakes to Avoid
- Installing a cartridge backward or without seating it fully
- Skipping plumber’s grease, which causes O-rings to tear or wear quickly
- Overtightening the packing nut, which can damage the seal
- Buying a part that matches the faucet style but not the brand or model
- Forgetting to shut off the supply valves before disassembly
Recommended Gear
- Plumber’s silicone grease: Keeps O-rings flexible and helps them seal properly during reassembly. View on Amazon
- Basin wrench: Reaches mounting nuts tucked behind the sink where a standard wrench won’t fit. View on Amazon
- Faucet O-ring and washer kit: Provides several sizes so you can replace worn seals without a special trip to the store. View on Amazon
For brand-specific steps, see How to Repair a Moen Sink Faucet: A Step-by-Step Guide for Common Problems and How to Repair a Leaking Delta Faucet: A Step-by-Step Guide. If the leak is at the bathroom sink, How to Repair a Leaking Faucet in the Bathroom: A Step-by-Step Guide covers the same process for that location.
FAQ
Why does my faucet keep dripping after I replace the cartridge?
The cartridge may be installed backward or not fully seated, or the new part may not match your faucet model. Remove it, check the orientation and confirm the retaining clip is locked in place.
Can I repair a leaking faucet without turning off the water?
No. Shutting off the supply valves under the sink is essential to prevent water spray and flooding during disassembly.
When should I call a professional?
If the faucet is corroded, the valve body is cracked, or the leak continues after you have replaced the cartridge and seals, a licensed plumber can check for deeper damage to the valve or supply lines.
Conclusion
Once you identify whether the leak comes from the spout, the handle base or the supply connections, the repair is usually straightforward. Replace the correct part, seat it properly and test the faucet at both low and full flow. With the right cartridge and a little grease, most sink faucets will stop dripping in a single afternoon.
