Updated November 2026
Delta faucet supply lines carry hot and cold water from the shutoff valves under your sink up to the faucet. When one wears out, bursts or starts weeping at a fitting, you can usually replace it yourself in about 20 to 30 minutes with basic tools. This guide covers how to pick the right line, shut off the water safely, and connect the new one without leaks.
Choose the Right Delta Faucet Supply Lines
Most Delta kitchen faucets use two flexible supply lines, one for hot and one for cold, each running from a shutoff valve to a connection on the faucet body. Lines are typically sold in lengths from about 12 to 20 inches, and the correct length depends on how far your valves sit from the faucet inlets. Measure the distance from the valve outlet to the faucet connection, then add a few inches so the line can curve without kinking.
Shopping for one? See our guide: 6 Best Delta Faucet Replacement Parts (2026): Expert Picks.
Check the connector end sizes as well. The valve end is usually a 3/8-inch compression nut, while the faucet end may be a 3/8-inch compression or a 1/2-inch nut, depending on the model. Look for stainless steel braided lines, which hold up better than vinyl or plastic-core versions. Your faucet’s installation manual or the parts diagram for your model will list the exact connection type.
Shut Off the Water and Remove the Old Lines
Turn the shutoff valves under the sink clockwise until they stop. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Then open the faucet to relieve remaining pressure and drain residual water into a bucket.
- Place a towel and a shallow bucket under the valves to catch drips.
- Loosen the compression nut on the shutoff valve with an adjustable wrench, holding the valve steady with a second wrench.
- Loosen the nut at the faucet end. Some Delta models use a plastic or brass nut that can be turned by hand once the line is loose.
- Pull the old line free and inspect the valve outlet for corrosion or a damaged seat.
Install the New Supply Lines Without Leaks
Before attaching the new line, check that the rubber washer or ferrule is seated inside each nut. Hand-tighten each connection first, then add roughly a quarter to a half turn with a wrench. Overtightening compresses the washer unevenly and can crack a plastic nut or split a brass fitting.
- Connect the faucet end first, since it is easier to reach while the line is loose.
- Attach the valve end and snug it by hand before using the wrench.
- Route the line in a loose curve, keeping it clear of the cabinet edges, drain pipe and garbage disposal.
Slowly open the shutoff valves about halfway. Watch each connection for drips while the line fills, then open the valves fully and run the faucet on hot and cold for a minute. Dry each joint with a paper towel and recheck after a few hours.
Tips for a Lasting Connection
- Do not use plumber’s tape on compression fittings, since it can prevent the washer from sealing.
- Replace shutoff valves at the same time if they drip, stick or do not close fully.
- Keep a spare line of the same length on hand if your sink has an older valve layout.
- Check the lines once a year for bulging, cracking or moisture at the nuts.
Recommended gear
- Stainless steel braided supply lines: The braided sheath resists bursting better than plastic-core lines, which makes them a common choice for replacement. View on Amazon
- Adjustable wrench set: Two wrenches let you hold the valve still while loosening the nut, which protects the shutoff valve from twisting. View on Amazon
- Bucket and towels: Catching residual water keeps the cabinet floor dry during disconnection. View on Amazon
FAQ
Can I reuse old Delta faucet supply lines?
It is better to replace them. Flexible lines age, stiffen and corrode at the fittings, and reusing a worn washer often causes a slow drip after reconnection.
How tight should the compression nuts be?
Hand-tighten first, then add about a quarter to a half turn with a wrench. Stop once the joint is snug and does not drip when water is turned on.
What should I do if a valve leaks after I replace the line?
Turn off the water, tighten the nut slightly, and check the washer position. If the valve itself still drips, it may need replacing, and a licensed plumber can help if you are unsure.
Conclusion
Measuring carefully, shutting off the water and hand-tightening each connection will get you a leak-free result with Delta faucet supply lines. Take your time with the nuts and check the joints after the water is back on. For more repair help, see How to Repair a Leaking Delta Faucet: A Step-by-Step Guide and Replacing a Delta Faucet Cartridge: A Step-by-Step Guide (2026).
