Updated November 2026
Most Price Pfister faucet repair jobs come down to one of three parts: a worn cartridge, a failed washer, or a corroded valve seat. This guide walks you through identifying your faucet type, shutting off the water safely, and replacing the part that is causing the drip or low flow. Most repairs take under an hour with basic hand tools.
Identify Your Price Pfister Faucet Type
Price Pfister has made faucets with several internal designs over the years, so the first step is figuring out which one you have. Look at the handle movement and the base of the faucet. A single lever that rocks side to side almost always uses a cartridge. Two separate handles that turn to open and close usually use compression washers and rubber seats.
Shopping for one? See our guide: 7 Best Delta Kitchen Faucet Parts (2026): Repair-Ready Picks.
- Single-handle cartridge: One lever controls both temperature and flow. Drips often come from the spout area.
- Two-handle compression: Each handle turns a stem with a rubber washer. Drips typically appear at the spout even when the handle is fully closed.
- Ceramic disc: Smooth, quiet operation with no washers. Leaks are less common but usually point to a worn disc or seal.
If you are unsure, remove the handle cap first and photograph the internals. Manufacturer parts diagrams help once you know the model series. For model-specific cost and installation context, see Price Pfister Faucet Kitchen: Why Prices Vary and How to Choose.
Shut Off Water and Remove the Handle
Close both the hot and cold supply valves under the sink. Then open the faucet to drain remaining water and place a towel in the basin to protect the finish and catch small parts. Pry off the decorative cap on the handle with a flat-blade screwdriver or a thin plastic tool, remove the handle screw, and lift the handle off.
- Close the hot and cold supply valves under the sink.
- Open the faucet and let residual water drain.
- Remove the handle cap and handle screw.
- Unscrew the retaining nut or bonnet with an adjustable wrench, wrapping the jaws in tape to avoid scratches.
Replace the Cartridge or Washers
For a single-handle cartridge, pull the cartridge straight out using the retaining clip, then note its orientation. Install the replacement cartridge the same way, aligning the tabs with the faucet body. For two-handle models, remove the stem, replace the rubber washer and O-rings, and check the valve seat for pitting. Lightly coat new O-rings with plumber’s grease before reassembly.
Corroded or pitted valve seats can keep dripping even with new parts. A seat wrench can resurface or replace them. The general process is similar across brands, so Replace Kitchen Faucet Cartridge: Step-by-Step Repair Guide covers the cartridge removal method in more detail.
Reassemble and Test
Reverse the disassembly steps, hand-tighten nuts before using a wrench, and avoid overtightening, which can crack plastic components or damage seals. Slowly reopen the supply valves and check for leaks at the base and spout before running the faucet at full pressure.
Common Mistakes to Avoid
- Forgetting to shut off both supply valves, which leads to a sudden spray of water.
- Installing a cartridge backward, which reverses hot and cold or causes continuous flow.
- Skipping the valve seat inspection when the drip continues after new parts go in.
- Using pliers on chrome finishes, which leaves marks that are hard to remove.
- Mixing up similar-looking washers from different series.
Recommended Gear
- Plumber’s grease: Keeps O-rings sealed and moving smoothly during reassembly. View on Amazon
- Adjustable wrench with padded jaws: Protects the finish while loosening retaining nuts. View on Amazon
- Seat wrench set: Removes and replaces valve seats that are beyond simple cleaning. View on Amazon
FAQ
Do I need to replace the whole faucet to fix a Price Pfister drip?
Usually not. Most drips are caused by a worn cartridge, washer, or O-ring, and these parts are inexpensive and replaceable. A full replacement is only worth considering if the body is cracked or the finish is failing.
How do I find the correct replacement part for my model?
Check the model number on the faucet body or under the sink, then match it to the manufacturer’s parts diagram. Bringing the old cartridge to a hardware store also helps confirm the right fit.
Why is my faucet still dripping after replacing the cartridge?
The valve seat is the most likely cause, since worn or pitted seats cannot seal against a new cartridge. Inspect the seats for damage and resurface or replace them. Persistent problems may warrant a call to a licensed plumber.
Conclusion
With the right faucet type identified and the water shut off, most Price Pfister faucet repair jobs can be finished in a single session. Replacing the cartridge or washers and checking the valve seats addresses the majority of leaks. If the problem persists or involves hidden plumbing, consult a licensed plumber.
