Updated November 2026

Most single-handle faucet leaks come from a worn cartridge or a failed O-ring, and you can usually fix either one in under an hour with a few basic tools. This guide walks through how to repair a leaky faucet single handle from shutoff to test, so the drip stops and stays stopped. The steps below apply to most single-lever kitchen and bathroom faucets, though exact parts vary by brand.

Before You Start: Shut Off Water and Identify the Faucet

Close the under-sink shutoff valves, then open the faucet to drain any remaining water. Place a towel in the sink basin so small parts can’t wash down the drain. Next, identify the brand, since Delta, Moen, Kohler and Pfister use different cartridges and internal designs. The brand name is usually on the handle, the base or the spout, and a quick search of that name plus your model will show you which parts to buy.

Shopping for one? See our guide: Delta Single Handle Faucet Repair Kit Review: Features and Performance.

Remove the Handle and Access the Cartridge

Pop off the decorative cap on top of the handle with a flat blade or a thin screwdriver. Loosen the set screw underneath, which is often a hex screw, then lift the handle straight up. Remove the trim or escutcheon ring and the retaining nut or clip that holds the cartridge in place. Pull the cartridge out, noting which direction its tab faces so you can reinstall it correctly.

Replace the Cartridge or O-Rings

If the faucet drips from the spout even when the handle is off, the cartridge is the most likely culprit. Compare the old cartridge to its replacement to confirm they match in height, stem design and tab position. Many owners find that replacing the cartridge is faster and more reliable than cleaning it. If you prefer to keep the existing cartridge, remove the O-rings and inspect the seats in the faucet body for mineral buildup or scoring, then clean them gently and install new O-rings lubricated with plumber’s grease.

Key Steps Checklist

  1. Shut off both supply valves and drain the faucet.
  2. Remove the handle cap, set screw and handle.
  3. Take out the escutcheon and retaining nut or clip.
  4. Pull the cartridge and note its orientation.
  5. Install the new cartridge or O-rings, then reassemble in reverse order.
  6. Turn the water on slowly and test for leaks at the spout and base.

Reassemble and Test the Faucet

Reinstall the cartridge with the tab in the same position as before, then secure the retaining nut or clip. Put the handle back on and tighten the set screw snugly, without forcing it. Open the shutoff valves slowly to avoid a pressure surge, then run the faucet through its full range of hot and cold settings. A properly seated cartridge should stop all dripping at the spout when the handle is in the off position.

Common Mistakes and Tips

  • Don’t skip the shutoff step; even a small amount of trapped pressure can spray water.
  • Avoid overtightening the retaining nut, which can crack the plastic body.
  • Take a photo before disassembly so you can match the order of parts.
  • Use plumber’s grease sparingly on O-rings; too much can attract debris.
  • If the leak persists after a new cartridge, check the valve seats for wear or damage.
  • Plumber’s grease helps O-rings seal smoothly and extends their life. View on Amazon
  • Faucet cartridge puller lets you remove a stuck cartridge without damaging the body. View on Amazon
  • Brand-specific cartridge kit ensures the replacement matches your faucet’s design. View on Amazon

For a related walkthrough on a different fixture, see How to Fix a Leaky Kitchen Faucet: 5 Steps for Most Models and Kitchen Faucet With Single Handle: Types, Parts and How to Choose. If the handle itself wobbles after repair, Moen Faucet Handle Is Loose: How to Tighten It in 6 Steps covers that fix.

FAQ

Why does my single handle faucet still drip after replacing the cartridge?

The new cartridge may not be fully seated, or the valve seats inside the faucet body may be worn or scratched. Check that the tab is aligned and the retaining nut is secure before assuming the body needs replacing.

How long does a single handle faucet repair usually take?

Most homeowners finish a cartridge replacement in 30 to 60 minutes, though a stuck cartridge or corroded parts can add time. Keep the parts organized to make reassembly faster.

Do I need to call a plumber for a leaky single handle faucet?

Most cartridge replacements are manageable as a DIY job if you have basic tools. If you find corroded supply lines, water damage or a leak inside the wall, consult a licensed plumber.

Conclusion

A leaky single handle faucet usually comes down to a worn cartridge or O-rings, and the repair follows the same basic sequence on most models. Shut off the water, work methodically through the disassembly, and match the replacement parts to your brand. Take your time on reassembly, and the faucet should run drip-free for years.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.