Updated November 2026

Delta faucet installation instructions come down to four jobs: prepping the sink, mounting the faucet body, connecting the water supply and checking for leaks. Most Delta kitchen faucets can be installed in one to two hours with basic hand tools. The steps below apply to typical deck-mounted models, so always check the specific instruction sheet packed with your faucet.

Prepare the Sink and Gather Your Parts

Start by turning off the water at the shutoff valves under the sink, then open the faucet to drain the lines. Clear the cabinet, and place a towel or bucket under the work area to catch drips. Check the mounting hole size against your faucet base. Most Delta kitchen faucets use a single 1-3/8 inch hole, but some models need three holes or a larger deck plate.

Shopping for one? See our guide: 6 Best Delta Faucet Replacement Parts (2026): Expert Picks.

Before you begin, confirm you have everything on this list:

  • Adjustable wrench and basin wrench
  • Plumber’s putty or the gasket supplied with the faucet
  • Flexible supply lines (usually included)
  • Phillips screwdriver and flashlight
  • Old towel and a bucket

Mount the Faucet Body and Deck Plate

Apply the gasket or a thin ring of plumber’s putty to the base of the faucet, then feed the supply lines and hoses through the sink hole. Set the faucet on the deck and align it with the back of the sink. Working from underneath, slide the mounting washer and nut onto the threaded shank and tighten by hand first. Snug the nut with a basin wrench, but avoid overtightening, since excess force can crack the sink or distort the gasket.

If your faucet has a deck plate, set it in place before tightening the nut. Make sure the plate sits flat and the faucet is level and facing the correct direction before you finish the final turn.

Connect the Water Supply Lines

Attach the color-coded supply lines to the shutoff valves. Blue usually marks cold water and red marks hot. Hand-tighten each connection first, then add a quarter to half turn with a wrench. Delta’s connection nuts are designed to seal without much force, so stop as soon as the joint is snug.

Quick connection checklist

  1. Connect the cold line (blue) to the cold shutoff valve.
  2. Connect the hot line (red) to the hot shutoff valve.
  3. Attach the spray hose or sprayer connection as directed in your manual.
  4. Confirm the lines are not kinked or twisted.

Test for Leaks and Flush the Lines

Slowly open the shutoff valves, one at a time. Turn the faucet handle on and run both hot and cold water for about 30 seconds each. Check every joint and the base of the faucet for drips. If a connection seeps, shut off the valve and tighten the nut slightly. Once the water runs clean, check again after 15 minutes, since small leaks often show up after the lines pressurize.

Common Mistakes to Avoid

  • Overtightening the mounting nut, which can crack porcelain or stainless steel sinks.
  • Mixing up hot and cold lines, which reverses the handle function.
  • Skipping the gasket or putty, a common cause of base leaks.
  • Forgetting to flush debris from new supply lines before the final connection.
  • Cross-threading the connection nuts, which is easy to do in tight cabinets.
  • A basin wrench helps you reach and tighten mounting nuts in cramped spaces under the sink. View on Amazon
  • Braided stainless steel supply lines can replace the included hoses if you want a sturdier connection. View on Amazon
  • A flashlight with a clip or headband keeps both hands free while you work beneath the sink. View on Amazon

FAQ

Do I need a plumber to install a Delta faucet?

Many homeowners install Delta faucets themselves with basic tools, since most models include the necessary parts. If your sink is damaged, your supply lines are corroded, or the mounting holes don’t match, a licensed plumber can help. Consult a professional for any work involving gas lines or structural changes.

Why is my new Delta faucet dripping under the sink?

Dripping usually comes from a loose supply line connection or a gasket that isn’t seated properly. Tighten the connection nut slightly and check the base gasket for gaps. If the handle itself still drips, you may need to replace the cartridge instead.

How long should installation take?

For a first-time installer, expect roughly one to two hours, including sink prep and leak testing. Experienced DIYers often finish faster, but rushing increases the risk of leaks.

Conclusion

With the sink prepped, the faucet mounted, the supply lines connected and the connections leak-tested, your Delta faucet should be ready for daily use. Check the joints again after a few days of normal use to catch any slow seepage. Keep your instruction sheet handy for future repairs and part replacements.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.