Updated November 2026
To repair a faucet cartridge, you shut off the water, pull the cartridge out of the valve body, clean or replace the worn parts and reinstall it so the handle moves smoothly and the drip stops. Most homeowners can handle this job in under an hour with a screwdriver, an adjustable wrench and a few inexpensive parts. This guide covers how to repair a faucet cartridge step by step, plus the signs that tell you whether repair or full replacement makes more sense.
Confirm the Cartridge Is the Problem
Cartridge trouble usually shows up as a constant drip from the spout, water leaking around the handle, or a handle that feels gritty, loose or hard to turn. Before you take anything apart, turn the water supply under the sink fully off and open the faucet to drain the lines. If the leak comes from the base of the spout or from under the sink, a different part may be at fault.
Shopping for one? See our guide: 6 Best Kitchen Faucet Cartridge Replacement Picks for Repairs (2026).
How to Repair a Faucet Cartridge Step by Step
- Shut off the hot and cold supply valves under the sink, then open the faucet to relieve pressure.
- Remove the handle decorative cap, then the handle screw, and lift the handle off.
- Remove the bonnet nut or retaining clip. A wrench wrapped in tape protects chrome finishes.
- Pull the cartridge straight up. If it sticks, a dedicated cartridge puller works better than pliers, which can crack the housing.
- Inspect the cartridge for worn rubber seals, mineral buildup, and cracks in the stem or body.
- Clean the valve seat inside the faucet body with a soft cloth and remove any grit.
- Install a repair kit or replacement cartridge, lubricate the seals with plumber’s grease, and reseat it in the same orientation.
- Reassemble the handle, turn the water back on slowly and test for leaks at several handle positions.
Check the Orientation Before You Remove Anything
Many cartridges are keyed, so they only fit one way. Take a photo before you pull the cartridge, or mark the position of the index tab with a marker. Reversing a cartridge is one of the most common reasons a repaired faucet still drips.
Repair Kit or Full Replacement?
A repair kit typically includes O-rings, seals and sometimes a spring, and it works well when the cartridge body is intact. If the stem is pitted, the body is cracked, or the cartridge is an older discontinued model, replacing the whole unit is usually the more reliable choice. The table below summarizes the trade-offs.
| Situation | Best choice |
|---|---|
| Drip with intact cartridge body | Repair kit with new seals |
| Cracked or corroded body | Full cartridge replacement |
| Stiff or gritty handle | Clean, lubricate or replace |
| Brand or model no longer available | Universal replacement cartridge |
If you want model-specific help, the site’s guide to Replace Kitchen Faucet Cartridge: Step-by-Step Repair Guide walks through the same process with more detail on common fittings.
Recommended Gear
- Moen Faucet Cartridge Puller Tool helps you remove a stuck cartridge without scratching the valve body. View on Amazon
- Plumber’s grease for faucet seals keeps O-rings moving smoothly and prevents tearing during reinstallation. View on Amazon
- Delta faucet repair kit matches the seal sizes used in many Delta cartridges. View on Amazon
For a Moen-specific walkthrough, see How to Install Moen Faucet Cartridge: A Step-by-Step Guide. If your faucet is a Delta, How to Replace a Delta Kitchen Faucet Cartridge in 6 Steps (2026) covers the process in order.
Common Mistakes to Avoid
- Forgetting to shut off the water supply, which leads to a spray of water in your face.
- Using pliers on the cartridge stem, which can crack the plastic or brass.
- Reinstalling the cartridge in the wrong position.
- Skipping lubrication, which causes new O-rings to tear within weeks.
- Overtightening the bonnet nut, which can make the handle stiff.
FAQ
Can I repair a faucet cartridge without buying a new one?
Yes, if the cartridge body is intact. Many drips come from worn O-rings or seals, which a repair kit replaces at a fraction of the effort of a full swap.
How do I know which cartridge my faucet uses?
Remove the cartridge and read the markings on its top or base, or check the brand and model stamped on the faucet body. Matching that information to a replacement listing is the most reliable approach.
Why is my faucet still dripping after I replaced the cartridge?
The most common causes are reversed orientation, debris stuck in the valve seat, or a seal that was not properly lubricated. Reopen the faucet, clean the seat and check the cartridge position again.
Conclusion
Repairing a faucet cartridge comes down to shutting off the water, pulling the cartridge, inspecting it and replacing the worn parts in the correct orientation. Take photos during disassembly and use a proper puller so you can reassemble with confidence. If the cartridge body is damaged, replacing the unit is the safer long-term fix.
