Updated November 2026
Changing a faucet in your kitchen is a manageable weekend project if you work methodically. You will shut off the water, disconnect the old unit, mount the new one and check every joint for leaks. Most installs come down to the same few steps, and the biggest risks are skipped shutoff valves and mismatched hole spacing.
Check Your Sink Holes and Faucet Fit Before You Start
Before you buy or remove anything, count the holes in your sink or countertop. Single-hole sinks take a single-handle faucet, while three-hole layouts usually suit a widespread or centerset model. Measure the center-to-center distance between the holes if you plan to keep the same spacing. A deck plate or escutcheon can cover a mismatch of a few inches, but a larger gap usually means the new faucet will not sit flat.
Shopping for one? See our guide: 7 Best Delta Kitchen Faucet Parts (2026): Repair-Ready Picks.
Shut Off the Water and Remove the Old Faucet
Close the under-sink shutoff valves by turning them clockwise until they stop. Then open the faucet to release the pressure and let any remaining water drain. Place a towel and a bucket below the work area, since small amounts of water will come out of the supply lines when you disconnect them.
- Loosen the compression nuts on both supply lines with an adjustable wrench or basin wrench.
- Remove the nuts or clips holding the faucet base under the sink. A basin wrench reaches the mounting nuts most easily.
- Lift the old faucet out and scrape away any old putty, gasket or residue from the sink surface.
Install the New Faucet Step by Step
Follow the manufacturer’s instructions, since mounting hardware differs by model. Most new kitchen faucets need a gasket or base seal set on the sink before the faucet body goes in. Thread the mounting studs through the holes, then tighten the nuts evenly from underneath. Snug is enough; overtightening can crack a plastic base or deform a sink rim.
- Set the gasket or seal on the sink, then lower the faucet into position.
- Add the washers and mounting nuts from underneath and tighten them evenly.
- Connect the hot and cold supply lines to the faucet tails, using the included hoses if provided.
- Attach the spray hose or sprayer, if your model has one, and check that it routes freely.
Connect the Water Supply Correctly
Hot goes on the left and cold on the right when you face the sink, which matches most standard faucets. Hand-tighten each compression nut first, then give it about a quarter turn with a wrench. Over-tightening brass or plastic nuts is a common cause of drips later.
Test for Leaks and Adjust
Open the shutoff valves slowly, one at a time, while watching the connections. Run the faucet at low flow for a minute and check the supply lines, the base and the sprayer. Dry each joint with a paper towel and look for moisture. If you see a drip, tighten the nut slightly and retest, rather than cranking it down hard.
Common Mistakes
- Skipping the shutoff valves and getting soaked when the lines come loose.
- Reversing the hot and cold lines, which is easy to do under a crowded sink.
- Forgetting the gasket or base seal, which often leads to a leak at the countertop.
- Overtightening plastic mounting nuts, which can crack the base.
- Buying a faucet before checking whether the hole spacing matches your sink.
Recommended Gear
- Basin wrench: Reaches the mounting nuts tucked behind the sink so you avoid contorting your arm. View on Amazon
- Plumber’s putty: Seals the base of a faucet on certain sinks where a gasket is not supplied. View on Amazon
- Adjustable wrench: Handles the compression nuts on the supply lines without rounding them off. View on Amazon
If you plan to replace only one part rather than the whole unit, the Changing Kitchen Faucet Cartridge: A Step-by-Step Guide for Beginners walkthrough covers that job. For the removal stage, Take Off Kitchen Faucet: A Step-by-Step Guide for Beginners goes deeper. Owners replacing a head or spray unit often find Replacing Kitchen Faucet Head: A Step-by-Step Guide (2026) useful, and Parts of a Kitchen Faucet: 6 Best Replacement Picks Compared (2026) helps if you need individual components.
FAQ
Can I change a kitchen faucet without a plumber?
Yes, most homeowners can swap a standard faucet with basic hand tools. Consult a licensed plumber if you find corroded shutoff valves, damaged supply lines or any sign of water damage under the sink.
How long does a faucet change usually take?
A first-time install often takes a few hours, mainly because of access under the sink. Having the right tools and the parts laid out in advance speeds things up considerably.
What if the shutoff valves under my sink do not turn?
Stiff or seized valves are common in older homes. Close the main water supply to the house instead, and consider having a plumber replace the valves before you continue.
Conclusion
Changing a kitchen faucet comes down to matching the sink holes, shutting off the water and mounting the new unit with the right seal. Connect the supply lines carefully and test every joint before you use the sink for cooking. Take your time with the connections, and the new faucet should run leak-free for years.
