Updated November 2026

To change the kitchen faucet, you shut off the water, disconnect the old supply lines and mounting hardware, set the new faucet in place, and connect everything before testing for leaks. Most homeowners can finish a straightforward swap in one to two hours with basic hand tools. The steps below apply to most standard deck-mounted kitchen faucets, though your model’s instructions always take priority.

Before You Start: Check Your Sink and Faucet

Confirm that the new faucet matches your sink’s mounting holes. A single-hole faucet needs one opening, while a two-handle or three-hole model needs a matching layout. Measure the sink deck thickness too, since most manufacturers specify a maximum deck thickness for their mounting hardware. If you are unsure how to choose the right fit, How to Choose a Kitchen Faucet: A Step-by-Step Guide walks through the main factors.

Shopping for one? See our guide: 7 Best Delta Kitchen Faucet Parts (2026): Repair-Ready Picks.

Tools and Supplies You Will Need

  • Adjustable wrench and basin wrench
  • Bucket and old towels
  • Flashlight
  • Plumber’s putty or the gasket supplied with the new faucet
  • Penetrating lubricant for stuck nuts
  • Replacement supply lines if the old ones are corroded or brittle

How to Change Kitchen Faucet Step by Step

Step 1: Shut Off the Water

Turn off the shutoff valves under the sink by turning them clockwise. If the valves are stiff or do not close fully, shut off the main water supply to the house instead. Open the faucet to drain remaining water from the lines.

Step 2: Disconnect the Old Faucet

Place a bucket and towels under the sink. Disconnect the supply lines from the shutoff valves first, then remove the mounting nuts beneath the sink deck using a basin wrench. Lift the old faucet out from above, and pull any spray hose and weight out of the cabinet.

Step 3: Clean the Sink Deck

Scrape away old putty, sealant and mineral deposits so the new faucet base sits flat. A clean surface prevents leaks and keeps the gasket seated evenly.

Step 4: Install the New Faucet

Feed the supply lines and any spray hose through the mounting hole. Set the base or gasket in place, then tighten the mounting nuts or plate underneath by hand before finishing with a wrench. Avoid overtightening, which can crack plastic components or warp the base.

Step 5: Connect the Supply Lines and Test

Attach the supply lines to the shutoff valves, hand-tightening first and then giving each nut a quarter turn with a wrench. Open the valves slowly, run the faucet on hot and cold, and check every joint for drips. Tighten fittings slightly if you see moisture, but do not force them.

Common Mistakes to Avoid

  • Skipping the shutoff valve check, which can leave you with a flooded cabinet.
  • Reusing old supply lines that show cracks, bulging or mineral crust.
  • Overtightening plastic nuts or the mounting plate.
  • Forgetting to flush the lines before the final connection, which can clog the new aerator with debris.
  • Mixing up hot and cold lines. Standard practice places hot on the left and cold on the right.
  • Basin wrench: Reaches the mounting nuts tucked behind the sink, where a standard wrench cannot fit. View on Amazon
  • Flexible stainless steel supply lines: Replace aging rubber or braided lines during the swap to reduce the chance of a later leak. View on Amazon
  • Plumber’s putty: Seals the base of some faucets where a gasket is not provided. View on Amazon

FAQ

Do I need a plumber to change a kitchen faucet?

Many homeowners complete the job themselves, especially on single-hole models with flexible supply lines. If you find corroded shutoff valves or damaged pipes, consult a licensed plumber before continuing.

How long does it take to replace a kitchen faucet?

A simple replacement often takes one to two hours, while older sinks with stuck nuts can take longer. Plan extra time if you need to replace the supply lines or shutoff valves.

What if the new faucet leaks after installation?

Check the mounting nuts first and confirm the gasket is seated flat. If leaking continues at the handle or spout, How to Fix a Leaky Kitchen Faucet: 5 Steps for Most Models covers the most common causes.

Conclusion

Changing a kitchen faucet comes down to careful shutoff, clean disconnection, a snug mounting base and thorough leak testing. Work slowly, check fittings twice, and follow your manufacturer’s instructions for the specific model. With the right preparation, the job is manageable for most DIY homeowners.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.