Updated November 2026

Changing out a kitchen faucet is a manageable weekend project when you work in the right order. You will shut off the water, disconnect the old unit, mount the new faucet and check every connection for leaks. Most homeowners with basic hand tools can finish in one to three hours, depending on how cramped the space under the sink is.

Before You Start: Check Your Sink and Faucet Type

Look under the sink before you buy or remove anything. Count the number of holes in the sink deck, since single-hole, three-hole and four-hole layouts each use different faucet configurations. Note whether the faucet mounts through the deck or on the wall behind the sink, and check the spread between the water supply lines. Many faucets are designed for a standard 8-inch center-set spread, while others are widespread, so confirm your sink matches the new unit before you remove the old one.

Shopping for one? See our guide: Top 7 Delta Kitchen Faucets with Pull-Out Spray for Everyday Use.

If you are still deciding on a replacement, a guide like How to Choose a Kitchen Faucet: A Step-by-Step Guide helps you match style and features to your layout.

How to Remove the Old Kitchen Faucet

  1. Shut off the water supply valves under the sink by turning them clockwise until they stop.
  2. Turn on the faucet to drain remaining water and relieve pressure.
  3. Place a bucket and towels under the sink to catch residual water.
  4. Disconnect the supply lines from the shutoff valves using an adjustable wrench, and loosen the nuts on the faucet’s inlet tubes.
  5. Remove the mounting nuts or retaining clips that hold the faucet to the sink deck or the mounting plate.
  6. Lift the old faucet straight up and out of the holes. Clean any old plumber’s putty or sealant from the sink surface.

If the mounting nuts are corroded and won’t budge, apply penetrating oil, wait 15 minutes and try again. Avoid forcing them, since a cracked sink is far more expensive to fix than a stuck nut.

How to Install the New Kitchen Faucet

Prepare the Sink Deck and Gasket

Wipe the sink deck clean and dry. If the new faucet includes a rubber gasket or mounting plate, set it in place before lowering the faucet. Some manufacturers specify plumber’s putty instead of a gasket, so follow the instructions included with your model.

Mount the Faucet and Tighten Hardware

Feed the faucet body through the mounting holes and set it level. Work from underneath to thread the mounting nuts or clips onto the studs, then tighten them evenly by hand before finishing with a wrench. Snug is enough. Overtightening can crack the sink or distort the gasket.

Connect the Supply Lines

Attach the hot and cold supply lines to the faucet’s inlet tubes, then connect them to the matching shutoff valves. Hand-tighten each connection first, then give it a quarter to half turn with a wrench. Hot goes on the left and cold on the right in the standard setup, but check the labels on your specific model.

How to Test and Finish the Installation

  1. Open both shutoff valves slowly, a quarter turn at a time, to avoid a sudden surge of pressure.
  2. Turn the faucet on, run hot and cold water for about two minutes, and watch for drips at every joint.
  3. Check the aerator and spray hose for debris from the new lines, and clean them if the flow looks uneven.
  4. Dry each connection with a paper towel and recheck after 30 minutes. Slow seepage often appears only after the system has pressurized.

If a joint drips, tighten it a little more. If it keeps leaking, shut off the water, check that the washer or O-ring is seated correctly and retry. For ongoing drips after installation, see How to Fix a Leaky Kitchen Faucet: 5 Steps for Most Models.

Common Mistakes to Avoid

  • Skipping the shutoff step, which leads to a wet cabinet floor and a messy first attempt.
  • Using too much plumber’s putty or none at all when the model calls for it.
  • Cross-threading supply line nuts, which can strip the threads and cause a leak.
  • Buying a faucet whose mounting style does not match your sink holes or wall setup.
  • Forgetting to flush the new lines before judging flow, which can clog the aerator with debris.
  • Adjustable wrench: Lets you grip mounting nuts and supply line fittings without rounding them. View on Amazon
  • Flexible braided supply lines: Replacing old supply lines during installation reduces the chance of a future leak. View on Amazon
  • Plumber’s putty: Seals the base of many faucets to the sink deck when the manufacturer calls for it. View on Amazon

FAQ

Do I need a plumber to change a kitchen faucet?

Most homeowners can handle a straightforward swap with basic hand tools. If your shutoff valves are seized or your sink has unusual mounting requirements, consult a licensed plumber.

How long does it take to change out a kitchen faucet?

A typical replacement takes one to three hours, including removing the old unit and testing for leaks. Tight spaces under the sink or corroded hardware can add time.

What if the new faucet doesn’t fit my sink?

Check the number of holes and the center-to-center spread before buying, and confirm whether the faucet mounts through the deck or on the wall. If the sizes do not match, a deck plate or a different model may be needed.

Conclusion

Changing out a kitchen faucet comes down to shutting off the water, removing the old unit cleanly, and mounting and connecting the new one without overtightening. Test every joint before you walk away. With careful preparation, you can finish the job in a single session.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our kitchen faucets & sinks guides, checking product details against manufacturer specifications and owner feedback.