Updated November 2026
Learning how to disconnect a kitchen faucet takes about an hour for most homeowners and requires only basic hand tools. The process involves shutting off the water, disconnecting the supply lines, loosening the mounting nuts underneath the sink, and lifting the faucet out. Once you finish, the old faucet is free to remove, and the sink is ready for a replacement or repair.
Prepare the Sink and Shut Off the Water
Start by closing the shutoff valves under the sink, one for hot and one for cold. Turn them clockwise until they stop. Then open the faucet to relieve pressure and let any remaining water drain. Place a towel and a bucket beneath the work area, since a few tablespoons of water will usually drip out when you open the connections.
Shopping for one? See our guide: 7 Best Delta Kitchen Faucet Parts (2026): Repair-Ready Picks.
Disconnect the Supply Lines and Spray Hose
Next, detach the flexible supply lines from the shutoff valves using an adjustable wrench. Hold the valve steady with a second wrench so you do not twist the pipe behind the wall. If your faucet has a pull-down spray head, unclip the hose from the weight or docking bracket and feed it back through the deck hole. Many owners find it helpful to take a photo of the routing before they pull anything loose, which makes reinstallation far easier.
Remove the Mounting Nuts and Lift the Faucet
Under the sink, you will find a plastic or metal mounting nut on each threaded stud. On most two-hole or single-hole setups, a basin wrench reaches these nuts easily. Turn them counterclockwise and remove any mounting plate or washer. With the nuts off, lift the faucet straight up and out of the sink. If it resists, check for caulk or old plumber’s putty around the base and cut it away with a utility knife.
Tools You Will Need
- Adjustable wrench
- Basin wrench
- Bucket and towels
- Utility knife
- Flashlight
- Plumber’s putty or silicone caulk (for reinstallation)
Clean the Deck Surface Before Reinstalling
Once the faucet is off, scrape away old putty, caulk, and mineral deposits from the sink deck. A clean, dry surface helps the new faucet seal properly. Inspect the escutcheon and gasket as well, since worn gaskets are a common source of leaks when the faucet goes back in.
Common Mistakes
- Forgetting to close the shutoff valves, which leads to a sudden spray of water.
- Overtightening the supply line nuts and cracking the plastic fittings.
- Twisting the shutoff valve stem while holding it, which can cause a slow leak later.
- Skipping the photo or notes, then struggling to recall how the spray hose was routed.
- Pulling hard on the faucet before all nuts and lines are free.
Recommended Gear
- Basin wrench: Its angled head reaches mounting nuts in tight cabinet space where a standard wrench cannot fit. View on Amazon
- Adjustable wrench: A reliable general tool for loosening supply line nuts without rounding them off. View on Amazon
- Flashlight: Good lighting makes it much easier to see fittings under the sink. View on Amazon
If you plan to upgrade the faucet after removal, our guide to How to Choose a Kitchen Faucet: A Step-by-Step Guide can help you pick a replacement that fits your sink. For leak-related removals, How to Fix a Leaky Kitchen Faucet: 5 Steps for Most Models covers the common causes.
FAQ
Do I need to turn off the main water supply?
Usually no. Closing the individual shutoff valves under the sink is enough for most kitchen faucet work. Only shut off the main supply if the valves are stuck or leaking.
What if the shutoff valves do not close fully?
Old valves can corrode and stop sealing. In that case, shut off the main water supply and consider having a licensed plumber replace the valves before continuing.
Can I reuse the supply lines after disconnecting them?
Often yes, if they are not kinked, cracked, or leaking. Many people replace them anyway during a new faucet installation because they are inexpensive insurance against drips.
Conclusion
Disconnecting a kitchen faucet comes down to three things: shutting off the water, releasing the supply lines, and removing the mounting nuts. Work slowly, keep track of how parts fit together, and clean the deck before reinstalling. With these steps, the removal goes smoothly and sets you up for a successful replacement.
