Updated November 2026
Learning how to repair a faucet leak usually comes down to finding the source, shutting off the water and replacing one worn part. Most drips come from a worn washer, an O-ring or a failing cartridge, and a basic set of hand tools is enough for the job. This guide walks through diagnosis, disassembly, replacement and reassembly so you can stop the leak yourself.
Identify Where the Leak Is Coming From
Before you take anything apart, figure out which type of leak you have. A faucet that drips from the spout after it is shut off usually points to a worn washer, a compression seat or a cartridge that no longer seals. Water leaking from the base of the handle or around the body suggests a failed O-ring or packing nut. Leaks at the connection under the sink are a separate problem, often solved by tightening or replacing a supply line.
Shopping for one? See our guide: 6 Best Tub Faucet Repair Kits for Leaks and Drips (2026).
Shut Off the Water and Disassemble the Faucet
Close the shutoff valves under the sink, then open the faucet to drain the remaining water. Work over a towel or a sink plug so small parts do not disappear down the drain. Lay the parts out in the order you remove them, since this makes reassembly far easier.
- Pry off the decorative cap and loosen the handle screw with a Phillips or hex key.
- Remove the handle and unscrew the bonnet or cartridge retaining nut.
- Pull out the stem, cartridge or valve assembly.
- Take the old washer, O-ring or cartridge to a hardware store so you can match it exactly.
Replace the Worn Parts and Reassemble
Install the new washer, O-ring or cartridge, and apply a thin layer of plumber’s grease to rubber parts so they seat smoothly. Do not overtighten the retaining nut, since this can crack a plastic body or distort the seal. Reassemble in reverse order, turn the water back on slowly and check for drips at the spout and base.
| Leak location | Likely cause | Usual fix |
|---|---|---|
| Spout drips when off | Worn washer or cartridge | Replace washer or cartridge |
| Base of handle leaks | Failed O-ring | Replace O-ring |
| Leak under sink | Loose or cracked supply line | Tighten or replace line |
Repair Faucet Leak Problems That Return
If the drip comes back within a few days, the seat or valve body may be scored or corroded. Mineral buildup from hard water is a common cause, and a seat wrench can resurface the seat. If the metal is pitted, replacing the whole cartridge or valve is more reliable than repeated patching. Owners of some brands also use model-specific repair kits, which bundle the exact parts needed.
Common Mistakes
- Skipping the shutoff valves and getting soaked when the handle comes off.
- Buying a washer by eye instead of matching size and thread.
- Overtightening the packing nut, which can crack the body.
- Forgetting which way the cartridge or stem faces during reassembly.
- Ignoring a leak at the base, which often gets worse over time.
Recommended Gear
- Plumber’s grease: Lubricates O-rings and washers so they seal without tearing. View on Amazon
- Faucet repair kit: Bundles common washers, O-rings and seals so you can match parts quickly. View on Amazon
- Seat wrench set: Lets you remove and resurface a corroded valve seat. View on Amazon
FAQ
Do I need to replace the whole faucet to fix a leak?
Usually not. Most leaks come from a worn washer, O-ring or cartridge, and replacing that single part costs far less than a new faucet.
How long does it take to repair a faucet leak?
For a first-timer, expect roughly one to two hours including shutting off water, taking the faucet apart and testing the repair.
When should I call a plumber?
If the valve body is cracked, the parts are seized or the leak continues after you have replaced the correct components, consult a licensed plumber.
Conclusion
To repair a faucet leak, locate the source, shut off the water, and replace the worn washer, O-ring or cartridge. Work methodically, keep parts in order and avoid overtightening. With the right replacement part, most drips stop for good in an afternoon.
